User manual LG P42W46XH

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. [. . . ] This feature can be used to prevent unauthorized viewing by locking out the front panel controls. This TV is programmed to remember which option it was last set to even if you turn the TV off. OPTION Language Input Label Key Lock Caption Set ID Power Indicator Initial Setting Move Enter OPTION Language Input Label Key Lock Caption Set ID Power Indicator Initial Setting Move Enter : English : Off : Off :1 : Home : English : On : Off :1 : Home Off On 1 MENU Select O P T I O N. PARENTAL CONTROL / RATING 2 3 ENTER Select Key Lock. I ENTER Select O n or O f f. I 4 RETURN Return to the previous menu. Return to TV viewing. MENU O In K e y L o c k `O n', if the TV is turned ) off, press the r / I, INPUT, CH (+ or -) button on the TV or POWER, INPUT, ( ) CH(+ or -) or NUMBER buttons on the remote control. With the K e y L o c k O n, the display ` !K e y L o c k' appears on the screen if any button on the front panel is pressed while viewing the TV. 89 APPENDIX TROUBLESHOOTING The operation does not work normally. I The remote control doesn't work Check to see if there is any object between the product and the remote control causing obstruction. Ensure you are pointing the remote control directly at the TV. I Ensure that the batteries are installed with correct polarity (+ to +, - to -). I Ensure that the correct remote operating mode is set: TV, VCR etc. Power interrupted. I Power is suddenly turned off The video function does not work. I Is the power cord inserted into wall power outlet?I Check your antenna direction and/or location. The instructions below are provided to help with programming software or to test functionality using telenet software. RS-232C Setup i. e) IN AUDIO (RGB/DVI) REMOTE CONTROL IN DIGITAL AUDIO OUT OPTICAL RS-232C IN (CONTROL & SERVICE) AUDIO OUT PR L R AUDIO ONENT IN S-VIDEO VIDEO L (MONO) AUDIO R AV IN 1 PC Type of Connector; D-Sub 9-Pin Male No. 1 2 3 4 5 6 7 8 9 Pin Name No connection RXD (Receive data) TXD (Transmit data) DTR (DTE side ready) GND DSR (DCE side ready) RTS (Ready to send) CTS (Clear to send) No Connection 1 5 Communication Parameters Baud rate : 9600 bps (UART) I Data length : 8 bits I Parity : None I Stop bit : 1 bit I Communication code : ASCII code I Use a crossed (reverse) cable. I 94 APPENDIX !NOTE G This product has command echo back in the RS-232C Command. 6 9 RS-232C Configurations Either cable below can be used. 7-Wire Configuration (Serial female-female NULL modem cable) PC RXD TXD GND DTR DSR RTS CTS 2 3 5 4 6 7 8 D-Sub 9 TV 3 2 5 6 4 8 7 D-Sub 9 TXD RXD GND DSR DTR CTS RTS RXD TXD GND DTR DSR RTS CTS 3-Wire Configurations (Not standard) PC 2 3 5 4 6 7 8 D-Sub 9 TV 3 2 5 6 4 7 8 D-Sub 9 TXD RXD GND DTR DSR RTS CTS Set ID Use this function to specify a TV ID number. G p. 98. OPTION Language Input Label Key Lock Caption Set ID Power Indicator Initial Setting : Home : Off : Off :1 Move Enter OPTION Language Input Label Key Lock Caption Set ID Power Indicator Initial Setting Move Enter : English : English : Off : Off APPENDIX :1 : Home F 1 Close G 1 MENU Select O P T I O N. 2 3 ENTER Select Set ID. Return to TV viewing ENTER 4 RETURN MENU 95 APPENDIX Command Reference List COMMAND1 COMMAND2 DATA (Hexadecimal) COMMAND1 COMMAND2 DATA (Hexadecimal) 01. Remote Control Lock Mode k x k k k k k k k k k k k a b c d e f g h i j k l m 00 ~ 01 (G p. 97) (G p. 97) 00 ~ 01 00 ~ 01 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 01 00 ~ 01 14. Backlight k k k k j m m m r s t u u b c g 00 ~ 64 00 ~ 64 00 ~ 64 00 ~ 02 (G p. 98) 00 ~ 01 (G p. 99) 00 ~ 64 COMMAND1 COMMAND2 DATA00 DATA01 DATA02 DATA03 DATA04 DATA05 (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) (Hexadecimal) 19. Channel Tuning m a physical major major low program high program low minor high minor low attribute Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the set. (j, k, m or x) [Command 2] : Second command to control the set. [Set ID] : You can adjust the set ID to choose desired TV ID number in Setup menu. When selecting Set ID `0', every connected the TV is controlled. [. . . ] In the event of termination under sections 8. 1 or 8. 2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by you or any distributor hereunder prior to termination shall survive termination. 8. 4. 8. 2. 9. UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL YOU, THE INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY DISTRIBUTOR OF COVERED CODE, OR ANY SUPPLIER OF ANY OF SUCH PARTIES, BE LIABLE TO ANY PERSON FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN IF SUCH PARTY SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY'S NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU. [. . . ]