User manual LG PQDSB

[. . . ] Do not pick the product with a sharp tool. It may cause product breakdown with the damage to its parts. I In-use Do not clean the product with strong cleanser such as solvent. Use soft clothes in order to prevent fire or product deformation. Do not touch the product with a wet hand. [. . . ] Connection cable for Dry contact Module (Linked Other equipment) 2. Connection cable for Air-conditioner PQDSB Defrost Slo Lo Med Hi Po Preheat Out door Room Temp Total on Central Run 3. LCD Screen Cooling Heating Auto Dry Fan FAN SPEED Wired Remote Controller 6 Junction Simple Wired Remote controller Part Description Junction Simple Wired remote controller ENGLISH PQDSB Defrost Slo Lo Med Hi Po Preheat Out door Room Temp Total on Central Run 1. Operation Display Panel Cooling Heating Auto Dry Fan 2. Fan Speed Button Each function will be shown on the display panel for three second or so when the power is applide at first. Group control switch 1. For group control use Ceiling height selection switch 1. High ceiling Indoor temperature sensor selection switch 1. Use the temperature sensor on the remote controller 2. Use the temperature sensor on the product. Use the sensor with the lower temperature between the remote controller and indoor unit. · When changing the group control switch, the power must be reconnected to reflect the changes. But we do not recommend this method. Installation Manual 13 Necessary functions before using ESP Function E. S. P function is setting the volume of each fan speed. It is for the convenience of installation. It is recommended that you should not use this function while using the remote controller. 1 PQRCFCS0 Press the room temperature button and temperature incrreasing button L same time for 10 seconds Defrost Preheat Out door Room Temp Total on Central Run 2 3 Set the volume of each fan speed(Low, Medium, Hi) by using the temperature control button. Press the fan speed button to select the fan speed. The value of E. S. P can be adjusted from 1 to 255. If you press the On/Off button while setting the ESP function, it will be canceled. (The picture on the left side is the example of setting the Hi wind to ESP 10. ) FAN SPEED 4 EX) Press the Fan Speed button and the temperature increasing button (L) at the same time for 2 seconds. Then the ESP setting will be activated after the temperature display flashes three times. Lo Med 200 Setting the Low wind to 210 100 Setting the Medium wind to 175 * The E. S. P value is set at the proper value at the factory. So it is highly recommended that you should do not change the E. S. P value at your discretion. Note : You can set the ESP only indoor is running. 14 Junction Simple Wired Remote controller Main Function of Remote Controller Main Function of Remote Controller On/Off Operation ENGLISH 1 On/off operation will operate if you press the On/Off button. You can not change the fan speed during Heating operation. [. . . ] code) 3 2 1 0 -1 -2 -3 Operation Table Contents Heating Mode Heating Mode Heating Mode Both Heating/Cooling OFF (Maintain normal Temp. ) Cooling Mode Cooling Mode Cooling Mode Owner's Manual 17 How to use the Mode Selection Button Fan Speed Selection You can easily control the fan speed. 1 Select the proper fan speed which you want by pressing the fan speed button on the remote controller. · If you press the fan speed button, the fan speed will change in the order of Low ¡ Medium ¡ Hi. · The initial fan speed is "Hi" · If the product is not compatible with the fan speed control, it will not function as per your selection. Fan Speed Selection in Cooling Operation PQRCFCS0 Defrost Preheat Room Temp Total on Central Run Lo Med Hi FAN SPEED Fan speed "Slo" can be select optionally depend on indoor product. 18 Junction Simple Wired Remote controller How to use the Mode Selection Button Neutral / Gap setting function ENGLISH 1 PQRCFCS0 Press the Room Temperature button(L) and None button at the same time for 10 seconds. Press 10 Sec. (into the mode) FAN SPEED Defrost 2 FAN SPEED Set the value of Neutral (code `0') by using the temperature control button(L/M). [. . . ]