User manual LG PQNFG14B0

[. . . ] It may cause product breakdown. If the product was submerged under water, ask the service center for instruction. It may cause fire or an electric shock unless you do that. Owner's & Installation Manual 3 Safety Precautions CAUTION Make sure children or senor citizens use the product under proper observation in order to prevent safety accident. Do not pick the product with a sharp tool. It may cause product breakdown with the damage to its parts. I In-use Do not clean the product with strong cleanser such as solvent. [. . . ] For group control/Slave use Ceiling height selection switch 1. High ceiling Product selection switch 1. Heat Pump product Indoor temperature sensor selection switch 1. Use the temperature sensor on the remote controller. Use the temperature sensor on the product. Use the sensors on the product and remote controller. · When changing the product selection switch and group control switch, the power must be reconnected to reflect the changes. · The central control could operate inappropriately depends on indoor unit type, when the remote controller is set as slave. 6 Simple Wired Remote Controller Installation Method Installation Method 1 Put the installation paper on the place and determine the position and height of the fixing screws of the wired remote controller. · Refer to the printed side of the installation paper. ENGLISH The position of the fixing screws CN-M C CN-ZONE CN-DISP IC01A C01K J14 Red Yellow Brown Side of remote Controller Side of Indoor Unit Main frame 3 Fixing the Remove the installation paper before installing remote controller the remote controller so that it can fit at the right place. 2cm * Do not embed the remote controller into the wall. (It may cause the breakdown of the temperature sensor. ) * If you want to install a number of remote controller at the same place in a vertical line, install them at regular intervals of 2cm. (It may cause the breakdown of the temperature sensor. ) * Do not install the cable with a distance of 50 m or longer. (This can cause communication error. ) * When installing the cable, check whether the connector between the remote controller and the product is installed properly. Instead the product will operate in several modes such as cooling, strong wind, comp-on. 1 PQRCUCA0 If you want to set the trial operation mode, press the mode button and the Fan speed button same time for three seconds. Defrost Preheat Out door Room Temp Total on Central Run 2 MODE FAN SPEED Then the product will begin the trial operation and the display will be like as shown on left side picture. 3 4 If you want to cancel the trial operation mode, just press the On/Off button. The trail operation will be shut down automatically after 18 minutes and system will go to the standby mode. * This function might not be available for Multi Product like Multi V system. Owner's & Installation Manual 9 Necessary function before using Celsius/Fahrenheit Switching 1 PQNFG14B0 If you want to change the temperature unit as the Celsius or Fahrenheit, press the Temperature control button( ) and the Fan speed button same time for three seconds to enter the setting Mode. Defrost Preheat Out door Room Temp Total on Central Run 2 TEMP MODE FAN SPEED TEMP Press the temperature control button to change the unit. Ex) Setting unit as Fahrenheit. Defrost Preheat Out door Room Temp Total on Central Run Defrost Preheat Out door Room Temp Total on Central Run <Setting as Celsius> <Setting as Fahrenheit> 3 After setting, press the Temperature control button( ) and the Fan speed button same time for three seconds to exit the setting Mode. The system will automatically release without input after 30 seconds. Defrost Preheat Out door Room Temp Total on Central Run 10 Simple Wired Remote Controller Necessary function before using Setting the Central-Control Address ENGLISH Please set the address while using the central controller. You don't need to set address if you don't use central controller. 1 PQNFG14B0 If you want to set the address on the display panel, press both temperature control buttons (L/M) same time for three seconds. Defrost Preheat Out door Room Temp Total on Central Run 2 3 Press the temperature-increasing button to change the group number. Press the temperature-decreasing button to change the indoor unit number. As shown on the left side panel, it displays 23. : 3 Set the address by pressing both temperature control buttons again(L/M) at the same time for three seconds. TEMP MODE FAN SPEED TEMP TEMP MODE FAN SPEED TEMP Group No. Indoor Unit No. · If you connect the indoor unit to the central controller, you should set the network address of the indoor unit so that the central controller could recognize it. · The center-control address is composed of the group number and the indoor-unit number. Note : The remote controller displays 'HL' if central controller has locked the remote controller . Owner's & Installation Manual 11 Necessary function before using ESP Function E. S. P function is setting the volume of each fan speed. It is for the convenience of installation. And press the mode button. Set the desired room temperature higher than the current room temperature. (16~30°C) Defrost Preheat Out door Room Temp Total on Central Run TEMP TEMP A click of the button will increase the desired temperature by 1°C. [. . . ] · By giving out air that has no difference of temperature with the indoors, it allows circulation of the room. * Temperature control is not available in the fan operation. 16 Simple Wired Remote Controller How to use the Mode Selection Button Fan Speed Selection ENGLISH You can easily control the fan speed. 1 Select the proper fan speed which you want by pressing the fan speed button on the remote controller. · If you press the fan button, the speed of the fan will change in the order of Low>Medium>Hi>Power. · The initial fan speed is "Hi" · If the product is not compatible with the Fan speed control, it will not function as per your selection. Fan Speed Selection in Cooling Operation PQNFG14B0 Defrost Preheat Out door Room Temp Total on Central Run Lo Med Hi TEMP MODE FAN SPEED TEMP Po Fan Speed Selection in Heating, Dry, Fan, Auto-Operation Lo Med Hi Owner's & Installation Manual 17 How to use the Mode Selection Button Indoor Temperature Display PQNFG14B0 1 Preheat Out door Room Temp Defrost When the fan speedbutton is pressed on the remote controller for about 3 seconds, the indoor temperature will be displayed for about 5 seconds, then goes back to the previous screen. [. . . ]