User manual LG PQRCUDS0B

[. . . ] Do not place a heating device near the product. It may cause an electric shock or product breakdown. Do not place something heavy on the power cable. It may cause fire or an electric shock. Do not place a heavy thing on the product. It may cause product breakdown. If the product was submerged under water, ask the service center for instruction. [. . . ] Press the temperature-decreasing button to change the indoor unit number. The number of the central control address group is "2. " And the number of the indoor unit is "5. " If you press the address setting button, the addressing setting mode will be unset. * If you connect the indoor unit to the central controller, you should set the network address of the indoor unit so that the central controller could recognize it. * The central control address is composed of the group number and the indoor-unit number. 3 Note : The remote controller displays 'HL' if central controller has locked the remote controller . 10 Deluxe Wired Remote Controller Necessary function before using ESP Function E. S. P function is setting the volume of each air flow. It is for the convenience of installation. It is recommended that you should not use this function whild using the remote controller. 100 unit 10 unit ENGLISH 1 2 3 Press the Special Function button. Press the E. S. P button. Set the volume of each air flow (Low, Medium, Hi) by using the temperature control button. (16~30°C) A click of the button will increase the desired temperature by 1°C. A click of the button will decrease the desired temperature by 1°C. * If the expected temperature is set lower than the current room temperature, the heating operation will not begin and just the blowing operation will continue. 3 Press the operation selection button and choose one of the functions among blowing, automation, heating, and dehumidification if you want another operation mode during the operation. 4 If you press the On/Off button, the heating operation will stop. What is the three-minute delay function?It will take a time for the product to blow warm air. The delay is just to protect the compressor. The room will be heated with warm air after three minutes when the compressor begins operation. I The cooling-only model will not do heating function. Owner’s & Installation Manual 13 How to use the Mode Selection Button Auto-Operation 1 2 Press the On/Off button and then press the Automatic Operation button. When the room temperature is lower than the expected temperature: Heating Operation. When the room temperature is higher than the expected temperature: Cooling temperature. 3 Press the operation selection button and choose one of the functions among blowing, automation, heating, and dehumidification if you want another operation mode during the operation. 4 If you press the On/Off button, the cooling operation will stop. ❈ The cooling-only model will show “AI” on the temperature display. AI could be adjusted by five levels (-2, -1, 0, +1, +2). ❈ This auto-operation is not related to "Auto Change Over" function. 14 Deluxe Wired Remote Controller How to use the Mode Selection Button Dehumidification Operation Dehumidification Operation: Dehumidification by lowering temperature slightly ENGLISH 1 2 3 4 Press the On/Off button on the remote controller. Select the dehumidification function by pressing the Mode selection button. When the dehumidification is being done, ”dh” will be shown on the display panel Press the operation selection button and choose one of the functions among blowing, automation, heating, and dehumidification if you want another operation mode during the operation. If used during the rainy season or high humidity, you can have both of effective dehumidifying and air conditioning effect. ❈ Temperature control is not available in the Dehumidification Operation. Fan Operation 1 2 3 4 Press the On/Off button on the remote controller. Select the Fan function by pressing the Mode selection button. When the Fan is being done, "fn" will be displayed on the display panel. Press the operation selection button and choose one of the functions among heating, automation, cooling and dehumidification if you want another operation mode during the operation. • Fan operation does not output cool air, but just the fan air. • By giving out air that has no difference of temperature with the indoors, it allows ventilation of the room. ❈ Temperature control is not available in the air fan operation. Owner’s & Installation Manual 15 How to use the Mode Selection Button Fan Speed Selection You can easily control the fan speed. 1 Select the proper fan speed which you want by pressing the fan speed button on the remote controller. • If you press the fan speed button, the strength of the fan speed will change in the order of Low ¡ Medium Hi ¡ Power. • If the product is not compatible with the fan speed control, it will not function as your selection. Fan Speed Selection in Cooling Operation Lo Med Hi Po Fan Speed Selection in Heating, Dry, Fan, Auto-Operation Lo Med Hi • If the indoor unit is compatible with the slo fan speed, you can adjust the air flow slow level. 16 Deluxe Wired Remote Controller Sub Function Sub Function Auto Swing ENGLISH You can control the wind direction easily. 1 2 Press the Sub function button on the remote controller. Press the automatic Auto Swing button. 3 A click of Auto Swing button will turn on/off the indicator. * If the product is not compatible with the automatic wind direction mode, it will not operate automatically. Owner’s & Installation Manual 17 Sub Function Plasma You can use the plasma function. 1 2 Press the Sub function button. Press the Plasma button. • A click of the Plasma button will turn on/off the indicator. • If the product is not compatible with the Plasma function, it will not do the Plasma function even though the indicator is turned on. • Plasma Function is possible when only product is operating. • Please press the Plasma button in Fan Mode, If you want to operate only plasma function. Ventilation You can use the ventilation function. 1 2 Press the Sub function button of the remote controller. Press the ventilation button. • A click of the ventilation button will turn on/off the indicator. [. . . ] If the Off icon blinks for a while and then stops on the time display panel, it is successfully set. To set for other days of the week, press the Day button and set the time in the same procedure. Press the Reservation button to exit the reservation mode. To cancel the Weekday reservation function, press the Reservation mode and then Cancel. If you see an outline box around the day of week, it means that time to start and end have been set. [. . . ]