User manual LG PTED0902GCA

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] If any items are missing, contact your dealer. User's Guide/Cards 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out. ) Or Power Cord AC-DC adapter (Depending on the country) AC-DC adapter (Depending on the country) DVI-D Signal Cable (This feature is not available in all countries. ) Screws NOTE This accessories may look different from those shown here. User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores to maintain standard compliance for the product. 4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting and Disassembling the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Use a coin on the back of the stand base and turn the screw clockwise to tighten. 3. Once assembled take the monitor up carefully and face the front side. When you desire to disintegrate the monitor from the stand base, use a coin to turn the screw counterclockwise. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 5 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display After installation, adjust the angle as shown below. * With stand base Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° Do not touch or press the screen when adjusting the angle of the monitor. The power indicator stays blue if the display is running properly (On Mode). If the display is in Sleep Mode (Energy Saving), the power indicator is blinking blue. 10 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: 1 2 3 4 Press the discretionary Button, then the main menu of the OSD appears. To access a control, use the corresponding Buttons. Use the Use the / Buttons to adjust the image to the desired level. Button to select other sub-menu items. Press the EXIT Button to exit from the OSD. 11 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. DSUB : D-SUB(Analog signal) input DVI-D : DVI-D(Digital signal) input HDMI : HDMI input Main menu Sub-menu BRIGHTNESS CONTRAST SHARPNESS BLACK LEVEL Supported signals DSUB DVI-D HDMI Description Standard image settings. PICTURE HDMI COLOR COLOR TEMP (PRESET) WARM MEDIUM COOL DSUB DVI-D HDMI Color temperature adjustments. (USER) SIX COLOR (RED/GREEN/ BLUE/CYAN/ MAGENTA/ YELLOW) HUE SATURATION RED GREEN BLUE GAMMA COLOR RESET DISPLAY HORIZONTAL VERTICAL CLOCK PHASE OVERSCAN DSUB To adjust the position of the screen To improve the clarity and stability of the screen DSUB HDMI HDMI VOLUME OTHERS LANGUAGE POWER INDICATOR WHITE BALANCE FACTORY RESET To adjust the volume To customize the screen status for a user's operating environment DSUB DVI-D HDMI DSUB DSUB DVI-D HDMI 12 On Screen Display(OSD) Selection and Adjustment Main menu Sub-menu ORIGINAL RATIO Supported input DSUB DVI-D HDMI Description SMART+ To adjust the image size DUAL WEB CINEMA MODE DSUB DVI-D MODE USER DSUB DVI-D HDMI It is a mode that the user can adjust each element. It can adjust the color mode of the Main Menu. It is a mode that the screen is adjusted to the best to view the videos. It is a mode that the screen is adjusted to the best for the text works. It is a mode that the screen is adjusted to the best to view pictures. [. . . ] Make sure to select the recommend resolution. The setting method can differ by computer and O/S (Operation System), and resolution mentioned above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer. 24 Troubleshooting Display image is incorrect G The screen color is mono or abnormal. · Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. [. . . ]