User manual LG PTHD0702DCA

[. . . ] MFL46896863 Welcome to LG Thank you for buying this LG video cassette recorder Model LV4787/PTHD0702DCA/LV4767/LV4765/LV4747/LV4745. Before using your video recorder you need to be familiar with the names of some of the buttons on the remote control handset (see OPERATING THE VIDEO RECORDER, pages 4 to 6), and you need to set up the video recorder so that it can receive the TV stations in your area and so that your TV set can receive pictures from it (see p 12 to 14). Installation POWER This Video Recorder operates on a mains supply of 200-240V~, 50 Hz. SERVICE Never remove the cover of the video recorder. There are no user serviceable parts inside. If it does not operate properly, unplug it and contact your dealer. PRECAUTIONS For safe operation and satisfactory performance of your video recorder, keep the following in mind when selecting a place for its installation. Shield it from direct sunlight and keep it away from sources of intense heat. Install the video recorder in a horizontal position only. [. . . ] Press the "OK" button. OFF 12 Pr-12 fSHARP OSD ON 16:9 OFF 4:3 TIME DATE + - SYSTEM AB C VCR OSD Dr. OPR DECODER OPR i 4 5 Press "D" and "E" repeatedly to select OFF, SOFT or SHARP. NOTE: This feature can only be operated when playing a tape. Press the "i" button to release it. 20 Other playback features Slow motion playback, Shuttle This video recorder is equipped with a slow motion and shuttle features. 1 2 3 4 During playing back or still picture press the cursor "F" or "G" button. You can reach the following playback speeds: (-7xplay, -3xplay, -play, still, 1/19 slow, play, 2xplay, 7xplay) If distortions can be seen in the picture, remove them with the cursor "D" and "E" buttons. To switch off the slow motion, press the desired function, e. g. playback, search, still picture or stop. The slow motion playback will only continue for about 30 seconds, after which the video recorder will return to normal playback mode, to avoid damage of the tape. When using the special playback effects (logic, picture search, still and slow motion playback) with a tape recorded in LP, there will be a loss of colour and there may be noise bars on the picture. Note: During Slow or Still playback, the noise bars can be appeared on the picture according to status of tape (especially NTSC recorded tape). In these cases adjust the tracking to playback a tape with the optimum picture quality. You can adjust the tracking with the cursor "D" and "E" buttons. 21 Other playback features Selection of the colour system Because your video recorder is equipped with dual colour standard, you can playback recordings in PAL B/G and SECAM B/G. During playback your video recorder detects the recorded colour system automatically. "RECP" will appear for a few seconds on the TV screen. To continue recording press the "P/STILL" button again. Press the "STOP" button to stop recording. "STOP" will appear for a few seconds on the TV screen. 23 Using the video recorder to record Recording one TV programme while watching another You can record one programme while watching another by selecting the channel you watch on your TV set. 1 2 3 Start a recording by following above steps 1 to 5 (see p. Select to TV mode by pressing the "TV/VCR" button on the remote control. "VCR" indicator will disappear on the video recorder's display. Select the TV station you want to watch with the programme channel selector on your TV set. Immediate timer (ITR) When making a recording you can set your video recorder to stop after a set period of time. 1 2 Press the "REC/ITR" button to start recording. Press the "REC/ITR" button several times until the desired recording time is shown on the video recorder's Display. Each time you press this button the ITR time will be extended by 30 minutes. The maximum time that can be set is 9 hours. When the ITR recording have been completed, the video recorder will stop and switch itself off. 3 To cancel a ITR recording, press the "POWER" or the "STOP" button. 24 Programming the video recorder timer The timer allows you to record broadcasts automatically. Up to 7 recordings within one month can be programmed at the same time. Introduction to ShowView (LV4787/LV4767/LV4747) ShowView programming lets you set the video recorder to record programmes, by simply entering a ShowView Code. [. . . ] Manufacturer LG / GoldStar Zenith Samsung Sony Hitachi Code Number 1 (Default), 2 1, 3, 4 6, 7 8, 9 4 NOTES: O Depending on your TV, some or all buttons may not function on the TV, even after entering the correct manufacturer code. If you enter a new code number, the code number previously entered will be erased. When you replace the batteries of the remote, the code number you have set may be reset to the default setting. Set the appropriate code number again. O O 37 Specifications General Power Power consumption Video Head system Tape speed Tape format Maximum recording time Rewind time Dimensions (W X H X D) Weight Operating temperature Operating humidity Timer : 200-240V~, 50Hz. [. . . ]