User manual LG R1804

[. . . ] - Do not connect ground to telephone wires, lightning rods or gas pipe. Do not place anything containing liquid on top of the set. - This may cause a fire or could give an electric shock. Do not insert any object into the exhaust vent. - This may cause a fire or could give an electric shock. Do not place heavy objects on the set. - This may cause serious injury to a child or adult. Do not use water while cleaning the set. - This may cause damaged the set or could give an electric shock. In case of smoke or strange smell from the set, switch it off , unplug it from the wall outlet and contact your dealer or service center. - This may cause a fire or could give an electric shock. Do not attempt to service the set yourself. Contact your dealer or service center. - This may cause damaged the set or could give an electric shock. During a lightning thunder, unplug the set from the wall outlet and don't touch an antenna cable. - This may cause damaged the set or could give an electric shock. WARNING/CAUTION TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. 2 Plasma Monitor Safety Instructions ENGLISH * Safety instructions have two kinds of information, and each meaning of it is as below. WARNING The violation of this instruction may cause serious injuries and even death. NOTES The violation of this instruction may cause light injuries or damage of the product. Take care of danger that may happen under specific condition. NOTES Never touch the power plug with a wet hand. - This may cause an electric shock. Disconnect from the mains and remove all connections before moving. Do not place the set in a built-in installation such as a bookcase or rack. - Ventilation required. When installing the set on a table, be careful not to place the edge of its stand. - This may cause the set to fall, causing serious injury to a child or adult, and serious damage to the set. Do not place an outside antenna in the vicinity of overhead power lines or other electric light or power circuits. - This may cause an electric shock. There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls. [. . . ] Press the G G G D /E button to select the TIMER menu. button and then use button and then use button and then use D / E button to select Clock. D /E D /E button to set the hour. Press the ENTER button to save the new settings. On/Off Timer Setup On/Off - Timer function operates only if current time has already been set. - Off-Timer function overrides On-Timer function if they are set to the same time. - If you do not press any button within 2 hours after the monitor turns on with the On Timer function, the monitor will automatically revert to standby mode. PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Clock Off timer On timer Auto off PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Clock Off timer On timer Auto off G On Off 6 : 30 AM 17 Volume Move Select Move Select 1. Press the G D /E button to select the TIMER menu. button and then use D /E button to select Off timer or On timer. 3. Press the G button and then use D / E button to select On. · To cancel On/Off timer function, select Off. Press the G G button and then use button and then use D /E D /E button to set the hour. button to set the minutes. G For only On timer function; Press the button and then use D /E button to set volume level. 6. Press the ENTER button to save the new settings. 24 Plasma Monitor Operation ENGLISH Auto Off Off - If there is no input signal, the Monitor turns off automatically after 10 minutes. PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Clock Off timer On timer Auto off PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Clock Off timer On timer Auto off G On Off Move Select Move Select 1. Press the G D /E button to select the TIMER menu. button and then use D /E D /E button to select Auto off. To avoid a permanent image on the screen, the image will move every 2 minutes. · Inversion Inversion will automatically invert the plasma display panel color every 30 minutes. Press the ENTER button to save the new settings. 26 Plasma Monitor Operation ENGLISH Low Power - Low power reduces the plasma display's power consumption. PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Language Key lock ISM Method Low power Set ID Index PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Language Key lock ISM Method Low power Set ID Index G On Off Move Select Move Select 1. Press the G G /E button to select the SPECIAL menu. button and then use button and then use D /E D /E button to select Low power. button to select On or Off. · When you select On, the screen darkens. Press the ENTER button to save the new settings. INDEX - Switches LED Display on or off. PICTURE Language SOUND TIMER SPECIAL SCREEN PIP/DW Key lock ISM Method Low power Set ID Index PICTURE SOUND TIMER SPECIAL SCREEN PIP/DW Language Key lock ISM Method Low power Set ID Index G On Off Move Select Move Select 1. Press the G D /E button to select the SPECIAL menu. button and then use D /E button to select Index. 3. Press the G button and then use D /E button to select On or Off. 4. Press the ENTER button to save the new settings. Owner's Manual 27 Operation Screen Menu Options Auto Adjustment RGB (PC) mode only; This function doesn't work for RGB(DTV). Automatically adjusts picture position and minimizes image shaking. [. . . ] Auto Configure only works in RGB-PC mode. Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 1 · Refer to `Real data mapping1'. Acknowledgement [u][ ][Set ID][ ][OK][Data][x] Data 1 * If you do not press any button within 2 hours after the monitor turns on with the On Timer function, the monitor will automatically revert to standby mode. 29. Key (Command2:c) G To adjust Key code for IR remote control. [. . . ]