User manual LG RH397D

[. . . ] Keep children away from the unit. 5 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. 6 Do NOT attempt to repair the unit yourself. If it is damaged in any way, contact: An authorized service center The dealer from whom you purchased the air conditioner. 7 Do NOT place any blocking objects in front of the unit. 8 If the remote control will not be used for a long time, remove the batteries. [. . . ] Each time you press the temperature buttons: Result: ­ The temperature is adjusted by 1°C and displayed on the control panel ­ The unit beeps The air conditioner starts cooling if the room temperature is higher than the selected temperature. 4 To set the fan speed to. . . Press the or Press the lights up Press the or Press the lights up Press the or Press the lights up button on the remote control. button on the unit until F3 button on the remote control. button on the unit until F2 button on the remote control. button on the unit until F1 Med Low Result: Each time you press a button, the unit beeps. 5 E-8 To control the direction of the air flow, refer to page 10~11. Airing Your Room ENGLISH If the atmosphere in your room is stale, you can air it using the Fan feature. When you operate the air conditioner, air flow blades are open and half closed automatically to give the proper air flow. 1 If necessary, press the (On/Off) button. The air conditioner starts up in the mode selected Result: when the unit was last used. The unit beeps twice. Remote Control Control Panel 2 If the Fan speed (F1, F2, F3) is not displayed on the unit: Press the button on the remote control or Press the button on the unit one or more times Until the fan speed (F1, F2, F3) is displayed. Result: The unit beeps each time you press the button. The air conditioner starts up in the Fan mode. When the air conditioner is in the Fan mode, the temperature is not displayed; in this case, you do not need to set the temperature. 3 To set the fan speed to. . . The fan will continue to run for a short time after the compressor cycles off. 2 If you would like the air conditioner to run in Fan mode, do not press the energy saver button. You cannot use the Fan mode in the energy saving mode. To stop the energy saving mode, press the energy saver button on the remote control again. Result: The fan runs at all times, while the compressor cycles on and off. If you select the Sleep Timer in the Energy Saving mode, the Energy Saving will be cancelled and the air conditioner will start up in the Sleep Timer mode. E-15 Operating Recommendation Here is a recommendation that you should follow when using your air conditioner. Topic Power failure Recommendation If a power failure occurs when the air conditioner is operating, the unit is switched off. When the power returns, the air conditioner starts up again automatically. The fan speed operates in the Med speed automatically to protect the air conditioner, especially in following conditions; the room temperature is going down below 23°C and the air conditioner is operating as the Low speed in the cool mode. If the room temperature is over 24°C, Low speed operates normally. Temperature and Humidity Ranges The following table indicates the temperature and humidity ranges within which the air conditioner can be used. Mode Cooling Indoor Temperature 21°C to 32°C approx. Outdoor Temperature 21°C to 43°C approx. The automatic protection feature may be triggered and the air conditioner stopped. A water leakage or some other malfunction may happen if the heat exchanger freezes. [. . . ] Do not, under any circumstances, cut or remove the third grounding prong from the power cord. We recommend that you should not use an extension cord or an adapter plug with this appliance. Do not change the plug on the power cord of this appliance. Follow national electrical codes or local codes and ordinances. 115V 15 AMP circuit "parallel" type 230V/208V 20 AMP circuit "perpendicular" type 230V/208V 15 AMP circuit "tandem" type 230V/208V 30 AMP circuit "tandem" type If the electric supply provided does not meet the above specifications, call a licensed electrician. [. . . ]