User manual LG RT-21FA20KEAEKLSLB

[. . . ] The temperature of unit's outside can be extremely high, please use the unit after proper installation in your vehicle. 8 cm CAUTION : This product uses a Laser System. To ensure proper use of this product, please read this owner's manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Performing controls, adjustments, or carrying out procedures other than those specified herein may result in hazardous radiation exposure. [. . . ] For safety, turn off the ignition before cleaning, and remove the key from the ignition switch. CAR CD/MP3/WMA Receiver 5 Installation Basic Installation Bend the claws according to the thickness of the dashboard ISO-DIN Installation Before installing, make sure that the ignition-switch is set to OFF and remove the terminal of the car battery to avoid short-circuiting. 1 2 3 4 Remove the existing receiver unit. Install the unit into the installation sleeve. 4 5 6 3 2 1 2 1 3 4 5 6 Control panel Control panel Slide the unit into the ISO-DIN frame. Slide the unit and frame into the dash opening. Install the dash panel or adapter plate. Install the control panel to the unit. Battery Installation 1 Removing the existing receiver unit A If there is already an installation sleeve for the receiver unit in the dashboard, it must be removed. 1 2 Remove the rear support from the unit. Remove the control panel and trim ring from the unit. Insert the lever A into the hole on one side of the unit. Perform the same operation on the other side and pull the unit out from the mounting sleeve. 2 3 Pull out the battery holder with a sharp product like a ball point pen. Pop t Classic t Rock t Jazz t Vocal t Salsa t Samba t User1 t User2 t Off Note When XDSS+ is set to "Off", you can adjust the EQ settings. Adjusting the sound level Press SEL (SEL/MENU on the remote control) repeatedly to select the mode you want to adjust from volume, balance and fader. Note 8 CAR CD/MP3/WMA Receiver Listening to the radio ON PLAYER 1. SRC BAND -?b / B?+ Press and hold -?b / B?+ ON REMOTE SRC 3 / BAND ?mm/MM?Press and hold ?mm/MM? Connecting USB device ON PLAYER 1. Moving to another drive ON REMOTE VOLUME Listening to the radio - more you can do Auto search memory Press U/AS. The six strongest broadcast frequencies will be stored under preset button 1-6 in the order of their signal strength. To cancel, press U/AS. Storing and recalling broadcast frequencies 1 Press BAND to select desired band you want to store. 2 Select the desired frequency and press one of preset buttons 1-6 and hold until the beep sound. 3 Repeat steps 1-2 to preset other stations. The next time, you press the same preset button, the radio station frequency is recalled from the memory. When connecting this unit to multi reader, press BAND/DRIVE (BAND/DRV on remote control) to go to the next drive. Each time you press the button, the driver modes changes. Note If the USB device is already connected, press SRC (SRC on remote control. ) to select a source to USB. To scan the preset stations Press u/PS. To cancel, press u/PS. Connecting an Auxiliary Equipment Auxiliary input To tune in the preset stations Press BAND to select the desired band and press the desired preset button 1-6 (preset button 1-6 on the remote control). [. . . ] REG OFF : The unit switches to another station, within the same network when the receiving signals from the current station become weak. (This mode, the program may differ from the one currently received. ) TA(Traffic Announcement) ALARM / SEEK TA ALARM : When a newly tuned station has no TP information for 5 seconds, a double beep sound is output. TA SEEK : When the newly tuned station does not receive TP information for 5 seconds, the receiver retunes to the next station which has the same PI as the last station, but has the TP information. PI (Programme Identification) SOUND / MUTE PI SOUND : If the sound of a station with different PI is heard intermittently, the receiver mutes the sound after 1 second. [. . . ]