User manual LG SATA INTERNAL DVD WRITER

[. . . ] Internal Drive English CAUTION : The laser used in the drive can damage your eyes. To reduce the risk of electric shock, do not remove cover (or back). Refer servicing to qualified service personnel. Use of controls or performance of procedures other than those specified herein may result in hazardous radiation exposure. WARNING : To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture Industry Canada requirement This class B digital apparatus complies with Canadian ICES-003. [. . . ] Discharge any static electricity on your person by touching the computer covers, etc. Removing the Computer Cover Make sure all peripheral devices of the computer and the computer itself are turned off, and then remove the cover. Refer to the manual for the computer for details about removing the cover. NOTE : There may be sharp edges inside the computer so take care to avoid injury. Mounting the Drive 1. Remove the 51/4 drive bay panel from the computer. Refer to the manual for the computer for details. Do not apply excessive pressure to the cables inside the computer. If there is not enough space behind the drive, connect the IDE and other cables before securing the drive. NOTE : This is a general installation guide. If your PC hardware appears different, please consult your hardware manual for installing peripheral devices. READ WRITE READ WRITE Jumper Setup Before installation, set the jumper on the jumper connector on the rear panel. The drive can be connected as the Master or Slave on an EIDE (ATAPI) interface. When several (up to four) EIDE devices are connected, each must be set in a unique way. Specific knowledge of hardware and software is necessary to install the drive. SL: Slave MA: Master NOTE : If two peripheral devices with the same settings are both connected to the Primary or to the Secondary EIDE bus, the host computer may fail to run or may malfunction. Careful attention is necessary. CS: Cable Select (CSEL) 4 NOTE : Only one jumper should be installed on the jumper connector. If more than one jumper is installed, the drive may malfunction or be damaged. Master/Slave setting is determined by jumper installation on the Jumper Connector. The following table shows the possible jumper settings. Name MA (Master) SL (Slave) CS (Cable Select) Function Drive set as Master Drive set as Slave Drive mode set by CSEL on the host IDE interface C S S L M A If you use CSEL setting, the MASTER/SLAVE setting will be made automatically, depending on the hardware configuration. For more details refer to the manual of your computer. PC Connection The drive connects to the motherboard of the host computer using an IDE interface cable. You may connect the Drive as a Slave or Master device, depending on your computer. To Install as a Master Drive To install the drive as a Master, the jumper can be left as supplied from the factory. Master drive (Booting hard disk) Master drive (CD/DVD drive) (Jumper left as Master) DIGITAL AUDIO DG Master drive (Booting hard disk) Master Drive (CD/DVD drive) (Jumper left as Master) DIGITAL AUDIO DG ANALOG AUDIO RG L CS M SLA INTERFACE 39 40 1 2 POWER +5 GND +12 - OR Motherboard Primary connector ANALOG AUDIO RG L CS M SLA INTERFACE 39 40 1 2 POWER +5 GND +12 DIGITAL AUDIO DG ANALOG AUDIO RG L CS M SLA INTERFACE 39 40 1 2 POWER +5 GND +12 Primary connector Slave drive (Other IDE drive) Secondary connector Secondary connector NOTE : A hard disk is normally installed as the Primary Master on the EIDE (ATAPI) interface. Other EIDE peripheral devices such as hard drives and LG drives are then set differently. 5 To Install as a Slave Drive To install the drive as a Slave, change the jumper setting on the rear panel to SL. Master drive (Booting hard disk) Slave drive - OR (CD/DVD drive) (Jumper set to Slave) Primary connector Master drive (Booting hard disk) Master drive (Other IDE drive) Slave drive (CD/DVD drive) (Jumper set to Slave) Secondary connector DIGITAL AUDIO DG ANALOG AUDIO RG L CS M SLA INTERFACE 39 40 1 2 POWER +5 GND +12 DIGITAL AUDIO DG ANALOG AUDIO RG L CS M SLA INTERFACE 39 40 1 2 POWER +5 GND +12 DIGITAL AUDIO DG ANALOG AUDIO RG L CS M SLA INTERFACE 39 40 1 2 POWER +5 GND +12 Connecting the Power Connector Connect the power cable from the computer's power supply to the socket on the drive unit, fitting the connector firmly into the power in connector. If there is no spare power cable available in the computer, you will have to purchase a splitter cable of a suitable type. NOTE : Improper connection may damage the drive and void the warranty. Generally, the power connector can only fit one way. [. . . ] etc. ) Please Note: Since this product supports Region Playback Control Phase II, a certain MPEG decoder card or Software without regional code setting may cause this drive not to read DVDROM discs. This Drive enables you to change the regional code up to 5 times. 11 Copyright © 2007 LG Electronics U. S. A. or http://www. lgusa. com LG Electronics Canada Inc. Ontario L4Z4G3 Canada LG Electronics Deutschland GMBH Jakob-Kaiser-Straße 12, D-47877 Willich, Germany LG Electronics U. [. . . ]