User manual LG T1710BP

[. . . ] *  eep the included accessories out of reach of babies or children as it can cause safety issues including K suffocation from swallowing the parts. * Make sure screws are tight against the wall, but do not overtighten. * Be careful not to install a TV that exceeds the weight restrictions of the wall mount. [. . . ] You may also need an 8 mm socket wrench or an Ø8 mm drill bit for concrete. 1 Fixating the mounting bracket on the TV - f the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and I refer to the technical service manual. Guide spacer Guide spacer screw <Work procedure> 1.  Check to see if the display has screws installed into the mounting holes.  Assemble the guide spacer and the guide spacer screw in order as shown in the picture. Lay the set down and secure the guide spacer and the set using the screws. -  ut the product on the table placing the screen face down. When doing this, it is highly recommended to place P a floor cushion or soft clothes on the flat table before putting the product on it to avoid any damage of the screen surface. -  ighten the screw until the set, guide spacer and the screw are fully pressing against one another. T - Use the "+" driver (Manual or motorized) when tightening the screw. 4 2 - Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and hallow block that do not crack. Please follow the below direction. - Check the material of the wall and the thickness of the finishing. -  hen installing the product on wall material not designated, install the product so that each fixated location W can withstand the pull out load of 70 kgf (686 N) and shear load of 100 kgf (980 N) or above. Anchor a b c Wall mount screw d e - Use the Ø8 mm drill bit for concrete and hammer (Impact) drill. → See A above, be sure to lift a product/speakers assembly by the product only, do not lift using only the speakers. ) →  hen installing a display rotated, only rotate the display 90 degrees (portrait mode). (Only applies for VESA W 200x200, 400x400) 5 How to level the Display After installing the display, check to make sure it is level. The wall mount has two screws that make minor adjustments to the level. ± 10 mm  (horizontal adjustment) 6 6 Tilt Angle Adjustment - The tilt angle can be adjusted after installation and setup. -  hen you adjust the angle, hold the product carefully with both hands to avoid any damage to the product W or wall. ➊ ➋ ➍ ➌ ➊ <Top Tilt> 12° ± 2° 10° ± 2° ➋ <Bottom Tilt> ➌ <Left Tilt> ➍ <Right Tilt> 10° ± 2° 12° ± 2° < Set Side > < Set Top > * The above numbers are the maximum allowed, some models may do less. → Use both hands when adjusting the angles. Do not place the hands on the TV’s back side or the wall mount while adjusting. → Two adult people who are capable of adjusting the tilt angle to need excessive force. →  When adjusting the number ➊ angle of the product, you must use both hands and then you can adjust the angle as shown above. → When adjusting the number ➋ angle of the product, you must use both hands and then you can adjust the angle as shown above. [. . . ] → When adjusting the number ➋ angle of the product, you must use both hands and then you can adjust the angle as shown above. → When adjusting the number ➌ angle of the product, you must use both hands and then you can adjust the angle as shown above. → When adjusting the number ➍ angle of the product, you must use both hands and then you can adjust the angle as shown above. 7 ENGLISH 7 How to adjust height + 80 mm + 80 mm Clamping bolt - 80 mm - 80 mm <When moving the set downward> <When moving the set upward> → It is possible to move the set upward and downward by as much as 80 mm. [. . . ]