User manual LG UW92

[. . . ] This product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the product and receiver. [. . . ] Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence. >> Operation is subject to the following two conditions: this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. The term "IC:" before the certification/registration number only signifies that the Industry Canada technical specifications were met. 2 UW92_DCANLL_ENG_2950 2/28/08 1:29 PM Page 3 IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the unit, unplug the unit from the outlet. When installing the product, ensure that the plug is easily accessible. Specifications Wireless Transmitter External dimensions (WxHxD) Net Weight Transmission Power Supply Wireless Receiver Power requirements Power consumption External dimensions (WxHxD) Net Weight Reception Output Amplifier Refer to main label Refer to main label 64x213. 6x252. 3 mm 1. 2 kg 2. 4 GHz 155 W + 155 W 52. 8x110. 5x140 mm. 0. 14 kg 2. 4 GHz DC 7. 5V max Designs and specifications are subject to change without pior notice. 4 UW92_DCANLL_ENG_2950 2/28/08 1:29 PM Page 5 Setting up Attaching the speakers to the Wireless Receiver a b Connect the power cord of the Wireless Receiver to the outlet. Connect the wires to the Wireless Receiver. Connect the Wireless Receiver and the rear speaker (right, left) with the speaker cable. b Attaching the Wireless Transmitter to the DVD receiver a b Connect the adaptor to the outlet and transmitter. Connect the SOUND SIGNAL connector of the Wireless Transmitter and rear (right, left) speaker of the main set with the sound signal cable. Connect the Ground cable to the DVD receiver. Be sure to connect the ground cable to the rear panel of the unit by using the screw in rear panel. If this is not connected, the wireless system will be come noise. a c b c a b a 5 UW92_DCANLL_ENG_2950 2/28/08 1:29 PM Page 6 Setting up Be careful of the following · Set the distance between this unit and Wireless Receiver within 10m. · Optimum performance can be implemented only when the Wireless Transmitter and the Wireless Receiver within distance of 2m to 10m is used since communication failure may occur if longer distance is used. [. . . ] Attach the ferrite core near the unit (Refer to the fig. 3 and comment. ). 3 Close the ferrite core until it clicks. (fig. 3) The length here is as short as possible. 6 UW92_DCANLL_ENG_2950 2/28/08 1:29 PM Page 7 LED indicator of Wireless Transmitter LED color BLUE RED OFF (No display) Setting an ID of Wireless Transmitter When the unit is manufactured, the ID is already set. If an interference occurs or you use a new Wireless Receiver, an ID is set again. Operation The main set is turned on, everything is connected and transmitting. The wireless transmitter is in standby mode. [. . . ]