User manual LG W2242TQ-BF

[. . . ] The casing cover should be opened only by qualified service personnel. Keep the monitor out of direct sunlight and away from stoves or any other heat source. Remove any object that could fall into the vents or prevent proper cooling of the monitor's electronics. Do not block the ventilation holes on the cabinet. [. . . ] Make sure the computer is turned on. Screen says q q q Make sure the vertical sync of input signal is within the range of 56 ~ 75 Hz. Change the refresh rate to 56~75Hz within 10 minutes. Re-power on monitor to start over again if you failed to change the refresh rate within 10 minutes. The Auto Function is designed for use on standard Macintosh or IBM-compatible PC running Microsoft properly Windows. It may not work properly if using nonstandard PCs or video card. q AUTO button not working properly q Imaging Problems q Display position is incorrect Image vibrates on the screen Vertical flicker appears q Push the Auto button. Adjust the image position using the Horizontal Position &/or Vertical Position in OSD Main Controls. Check that the signal cable is properly connected to the graphics board or PC. q q q Push the Auto button. Eliminate the vertical bars using the Clock Adjustment of VIDEO NOISE in OSD Main Controls. Horizontal flicker appears q q Push the Auto button. Eliminate the horizontal bars using the Phase Adjustment of VIDEO NOISE in OSD Main Controls. file:///D|/Grace/150P2/english/150p2m/safety/saf_troub. htm (1 of 2) [9/5/2001 11:09:19 AM] Troubleshooting q The screen is too bright or too dark q Adjust the contrast and brightness in OSD Main Controls. (The backlight of the LCD monitor has a fixed life span. When the screen becomes dark or begins to flicker, please contact your dealer. The complete environmental criteria document may be ordered from: TCO Development SE-114 94 Stockholm, Sweden Fax: +46 8 782 92 07 Email (Internet): development@tco. se Current information regarding TCO'99 approved and labeled products may also be obtained via the Internet, using the address: http://www. tco-info. com/ RETURN TO TOP OF THE PAGE Environmental Requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in fetus development may occur. The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries, the color-generating layers of display screens and the electrical or electronics components must not contain any cadmium. [. . . ] Centro de Informações ao Consumidor R. andar Phone: 0800-123-123 Fax : (0xx11) 3141-1580 CHILE Philips Chilena S. A. box 2687Santiago de Chile Phone: (02)-730 2000 Fax : (02)-777 6730 COLOMBIA Industrias Philips de Colombia S. A. -Division de Servicio CARRERA 15 Nr. 104-33 Bogota, Colombia Phone: (01)-9800-9-18971 (toll free) Fax : (01)-619-5377 MEXICO Consumer Information Centre Norte 45 No. 669 Col. [. . . ]