User manual LG W2363D

[. . . ] ENGLISH OWNER'S MANUAL LCD MONITOR Please read this manual carefully before operating your set and retain it for future reference. LCD MONITOR MODELS W2363D www. lg. com Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. [. . . ] Once assembly is complete the monitor up carefully and position for use. 6. To disconnect the Stand Base from the Stand Body, simply unfold the screw handle and turn "counter-clockwise" to loosen the screw and disconnect the Stand Base from its body. IMPORTANT This picture depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or cause injury. 6 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5° to 15° -5 15 Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. 7 Connecting the Display Connecting with the PC/AV equipment 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable 1 screws of the signal cable. and power cord 2 in order, then tighten the A Connect DVI-D (Digital signal) Cable B Connect HDMI Cable (HDMI1, HDMI2) NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. AV equipment (Set-Top Box, DVD, Video, Video Game Console) * HDMI is optimized on the AV equipment. * Not supported PC. Varies according to model Headphone/Earphone output Wall-outlet type PC Speaker Out/Line out DVI-D 3. Press the Power Button ( ) on the front panel to turn the power on. 8 Control Panel Functions Front Panel Controls Button Use this button to enter THRU MODE, SRS TRUSURROUND HD, ARC or AUTO BRIGHT menus. For more information, refer to page 13 to 14. SOURCE Button When two input signals are connected, you can select the input signal (DVI-D/HDMI1/HDMI2) you want. When only one signal is connected, it is automatically detected. MENU Button Use this button to enter or exit the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. 9 Control Panel Functions Buttons Use these buttons to select or adjust functions in the On Screen Display. SET Button This button is used to enter a selection in the On Screen Display. TRU-LIGHT Button You can select GAME, MOVIE or MUSIC by using this button and the LED light shape will change according to each mode. When you select OFF, the LED light will be turned off. TRU-LIGHT GAME MOVIE MUSIC OFF Power Button Use this button to turn the display on or off. Power Indicator The power indicator stays blue if the display is running properly (On Mode). If the display is in Sleep Mode (Energy Saving), the power indicator is blinking blue. 10 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. [. . . ] · Check whether volume is "0". · Check whether the cable is correctly connected. (DVI-D cable, HDMI cable, Headphone cable, Audio cable) · Check sound format. Not supply to compressed sound format. IMPORTANT Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. [. . . ]