User manual LG W2600V-PF

[. . . ] User's Guide W2600V Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to your dealer when you ask for service. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national standards if not being provided by the supplier. If the power cable is faulty in any way, please contact the manufacturer or the nearest authorized repair service provider for a replacement. [. . . ] USB allows you to connect a chain of up to 120 devices on a single USB port; and you can "hot" plug (attach them while the computer is running) or unplug them while maintaining the Plug and the Plug auto detection and configuration. This display has an integrated BUSpowered USB hub, allowing up to 2 other USB devices to be attached it. 1. 2. Connect the upstream port of the display to the downstream port of the USB compliant PC or another hub using the USB cable. (Computer must have a USB port) Connect the USB compliant peripherals to the downstream ports of the display. USB downstream Port x (4) Connect the cables from USB compliant peripherals-such as mouse, memory stick or USB hard disk, etc. USB upstream Port x (1) Connect to downstream connectors of desktop or laptop computers. (However, the computer must support USB and have the USB port. ) 3. The monitor's USB terminal supports USB 2. 0 and High Speed cables. High Speed Data Rate Power Consumption 480Mbps 2. 5W (Max, each Port) Full Speed 12Mbps 2. 5W (Max, each Port) Low Speed 1. 5Mbps 2. 5W (Max, each Port) NOTE To activate the USB hub function, the display must be connected to a USB compliant PC(OS) or another hub with the USB cable(enclosed). When connecting the USB cable, check that the shape of the connector at the cable side matches the shape at the connecting side. Even if the display is in a power saving mode, USB compliant devices will function when they are connected the USB ports(both the upstream and downstream) of the display. 8 Connecting the Display To arrange the cables Connect the power cord and the signal cable as shown in the figure and then fix them to the cable holders 1 and 2. 1. Please insert the cable holder1 into the hole. 2. Please put the power cord and the signal cable in the cable holder 1. Cable holder 1 3. Please put the power cord and the signal cable in the cable holder 2. While pressing the bottom of cable holder 2 with one hand, pull the top of it with the other hand as shown in the picture. Pull Press Cable holder 2 9 Control Panel Functions Front Panel Controls Button Use this button to enter EZ ZOOMING, 4:3 IN WIDE, PHOTO EFFECT, SOUND items, for more information, refer to page 15 ~ 16. Button Use this button to enter On Screen Display Sub-menu to adjust BRIGHTNESS directly. MENU Button Use this button to enter or exit from the On Screen Display. OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that these settings are not inadvertently changed. To lock the OSD settings, press and hold the MENU button for several seconds. The message "OSD LOCKED" appears. You can unlock the OSD settings at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" appears. 10 Control Panel Functions Buttons Use these buttons to select or adjust functions in the On Screen Display. For more information, refer to page 21~22. (SOURCE Hot key) When 2 sets of computers are connected, you can select the input signal you want (RGB/DVI/HDMI). The default input signal is RGB. INPUT RGB DVI HDMI AUTO/SET Button Use this button to enter a selection in the On Screen Display. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Touch the MENU Button, then the main menu of the OSD appears. Main Menu MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu : Restart to select sub-menu Button Tip Menu Name Icons Sub-menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. 14 On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the bottom of the monitor. button on the left SOUND M E N U : Exit , : Move AUTO/SET : Select Main menu Description To select the adjust the resolution. When you select EZ ZOOMING in OSD, display resolution goes one step down so characters and images look bigger. When you select EZ ZOOMING once again, it goes back to the original resolution. EZ ZOOMING * To use this function, you must install forteManager program. For details, refer to the forteManager Installation Guide on the CD-ROM. * forteManager is not supported for HDMI input. To select the image size of the screen. 4:3 IN WIDE WIDE 4:3 1:1 · WIDE : Switch to full screen mode according to input image signal. · 4 : 3 : Change the image signal ratio into 4:3. [. . . ] If the results are unsatisfactory, decrease the vertical bars or stripes using the CLOCK icon in the on screen display. · Touch the AUTO/SET button to automatically adjust your display image to the ideal setting. If the results are unsatisfactory, decrease the horizontal bars using the PHASE icon in the on screen display. · Check Control Panel --> Display --> Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting. [. . . ]