User manual LG WM2477HW

[. . . ] The power supply cord is used as the main disconnection device. Ensure that the socket-outlet is easily accessible after installation. Operate the display only from a power source indicated in the specifications of this manual or listed on the display. If you are not sure what type of power supply you have in your home, consult with your dealer. [. . . ] Place the monitor with its front facing downward on a soft cloth. Assemble the stand base into stand body in the correct direction as shown in the picture, then tighten the screw which is attached to the stand base. Stand Body Stand Base Screw 3. Once assembled take the monitor up carefully and face the front side. Disassembling the stand 1. Place the monitor face down on the cushion or soft cloth. Loosen the screw which is attached to the stand base, then take off the stand base from stand body. Stand Body Stand Base Screw Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. A4 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5°~15° Swivel Range: 355° Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. A5 Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map form 1 to 2 . NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. When the icon you want becomes highlighted, press the AUTO/SET Button. Use the / Buttons to adjust the image to the desired level. Use the AUTO/SET Button to select other sub-menu items. Push the MENU Button once to return to the main menu to select another function. Push the MENU Button twice to exit from the OSD. A10 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu CINEMA MODE AUTO BRIGHT TIME CONTROL LIVE SENSOR SMART EZ ZOOMING 4:3 IN WIDE PHOTO EFFECT VOLUME PICTURE BRIGHTNESS CONTRAST GAMMA **BLACK LEVEL sRGB PRESET 6500K 9300K RED GREEN BLUE HORIZONTAL VERTICAL CLOCK PHASE SHARPNESS LANGUAGE HORIZONTAL OSD POSITION VERTICAL *WHITE BALANCE **OVERSCAN RTC POWER INDICATOR FACTORY RESET MOVIE *INTERNET **GAME USER *NORMAL **STANDARD *DEMO **SPORTS NORMAL GAUSSIAN BLUR SEPIA MONOCHROME Sub-menu AD H Reference To focus on the moving picture selected. To control screen brightness automatically. To adjust the resolution To adjust the image size To adjust screen color mode To adjust the volume To adjust the brightness, contrast and gamma of the screen To set offset level COLOR To costomize the color of the screen To adjust the position of the screen To improve the clarity and stability of the screen TRACKING SETUP To costomize the screen status for a user's operating environment FLATRON F-ENGINE To select or customize desired image settings G : Adjustable * : only for DSUB/DVI Input ** : only for HDMI Input A : DSUB Input D : DVI Input H : HDMI Input NOTE The order of icons may differ depending on the model (A11~A20). A11 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Main Menu MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu : Restart to select sub-menu Button Tip Menu Name Icons Sub-menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. A12 On Screen Display(OSD) Selection and Adjustment Main menu PICTURE Sub menu Description PICTURE DSUB/DVI input BRIGHTNESS CONTRAST GAMMA To adjust the brightness of the screen. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. If you select 'HIGH', the screen will be bright and if you select `LOW', the screen will be dark. [. . . ] · Try to turn on the PC. G Do you see an "OUT OF · This message appears when the signal from the PC (video card) is out of horizontal or vertical RANGE" message on frequency range of the display. 'Specifications' section of this manual and configure your display again. G Do you see a "CHECK SIGNAL CABLE" message on the screen?· This message appears when the signal cable between your PC and your display is not connected. [. . . ]