User manual LIEBHERR CNESF 5123 COMFORT NOFROST

[. . . ] Take the packaging material to an official collection point. - in staff kitchenettes, bed and breakfast establishments, - by guests in cottages, hotels, motels and other forms of accommodation, - in catering and similar services in the wholesale trade. Use the appliance solely as is customary within a domestic environment. All other types of use are inadmissible. The appliance is not suitable for storing and cooling medicines, blood plasma, laboratory preparations or similar substances and products covered by the 2007/47/EC Medical Devices Directive. Any misuse of the appliance may result in damage to or spoilage of stored goods. [. . . ] The LED will stop flashing and will light continuously. The LED will go out as soon as the temperature in the freezer compartment is low enough. You can re-arrange the storage shelves as required. Equipment GB Lift the glass shelf, align the recess over the support and replace the shelf in a higher or lower position. This can be caused by: • the freezer door being left open for a long time, allowing warm ambient air to enter; • a long power failure; • a fault in the appliance. In each case, make sure food has not thawed or perished. If the visual warning LED does not go out, contact the customer service department (see section on "Malfunctions"). - By shifting the bottle holder F you can protect the bottles from falling over when opening or closing the door. Repositioning the door racks - Lift door rack vertically (1), lift out to the front and re-insert at a different height, following these steps in the reverse order (2). Using the sectioned shelf Place the shelf rails provided, fig. 1, on the supports on the left and right at the desired height. - Always ensure good ventilation. Do not cover ventilation openings or grille. - Avoid positioning the appliance in direct sunlight or near cookers, radiators and similar sources of heat. - The energy consumption depends on the installation conditions, e. g. - Keep the time the appliance is open to a minimum. - Keep all food properly packed and covered so as to avoid its frosting up on the outside. - Always allow hot food to cool to room temperature before placing in the appliance. Open the front flap and fill the water tank while still in the appliance with water using a jug or bottle. Filling the water tank The ice cubes fall out of the ice maker into the drawer. When the ice reaches a certain level in the drawer, the appliance stops producing ice automatically. If you require a large quantity of ice you can swap the drawer to the right with the full "IceMaker" drawer. When you close the drawer the ice maker will immediately start production. 2. The water tank can also be removed completely to be filled with water. 3. Reinsert the water tank and slide into the holder as far as it will go. Important If the water tank has not been slid right to the back, no ice cubes will be produced. 17 Refrigerator compartment Defrosting Cleaning the ice-cube tray Freezer compartment The refrigerator compartment defrosts automatically. The water that forms on the rear wall drains into a reservoir at the back of the appliance and evaporates automatically through the compressor heat. Ensure that the water can flow without hindrance through the hole above the vegetable bins. The NoFrost system automatically defrosts the appliance. Any moisture arising collects on the evaporator and freezes, and is periodically defrosted and evaporated. • The ice maker must be switched on. The ice-cube tray can be cleaned. Use the following method. • Remove any ice cubes from the drawer. • Hold the ON/OFF button for 10 seconds (after 1 second the ice maker will switch off - the LED will go out). • After you have held the ON/OFF button for 10 seconds the LED will start to flash for 60 seconds. [. . . ] – Is the appliance set up too close to a heat source?If none of the above causes apply and you cannot rectify the fault yourself, contact the nearest customer service department stating the type designation 1, service number  2 and appliance number  as 3 indicated on the type plate. The position of the type plate is shown in the section entitled Description of the appliance. Malfunctions To adapt the height of the appliance to the surrounding furniture a top unit 1 can be added. A gap of at least 50  mm depth must be provided behind and along the entire width of this unit so as to ensure sufficient ventilation. [. . . ]