User manual LIEBHERR UIK 1550 PREMIUM

[. . . ] Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Saving energy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Controls and displays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Condensate is prevented from forming between the appliances by the foamed-in side wall heating on the left side of the freezer. Pay attention that the socket is readily accessible. 3 4 Putting into operation Recess height A 820 mm 820 mm 870 mm 870 mm Height of unit plinth B 100 mm 170 mm 150 mm 220 mm Height of unit door C 716 mm 646 mm 716 mm 646 mm Base height of unit plinth D 100 mm 100 mm 150 mm 150 mm Note u Before assembling the door of the unit, make sure that the admissable weight of the unit door is not exceeded. u Otherwise damage to the telescopic rails and resultant malfunction cannot be ruled out. weight of unit door 10 kg 4. 3. 1 Installing the appliance u Detach the connecting cable from the rear of the appliance, removing the cable holder at the same time because otherwise there will be vibratory noise!u Lay the connecting cable with the help of a string in such a way that the appliance can be easily connected after fitting. Fig. 5 Built-under variants: Slide in and align the appliance: NOTICE Risk of harm to flooring susceptible to damage!10 cm x 60 cm, under the height-adjustable feet on either side. u After the appliance has been slid in, remove the strips. Fig. 6 for recess height 820 or 870 mm A = Height of recess B = Height of unit plinth C = Height of unit door D = Base height of cut-away unit plinth u Pull the plinth panel forwards to remove it. w The distance of the front edge of the side wall of the kitchen unit to the appliance body is 41. 5 mm all the Fig. 17 4. 4 Adjusting the contact of the door seal It may be necessary to adjust the appliance door, depending on the weight of the kitchen unit door. Once the kitchen unit door has been fitted, see that the door seal makes full contact with the appliance body. 7 Putting into operation Fig. 20 The means for adjustment is situated on the right and left underneath the bottle rack on the door interior. The following adjustments are possible: q Inclination ± 1° q Upward adjustment by 4 mm q Downward adjustment by 2 mm q Adjustment by 2 mm to the left and right, respectively NOTICE Functional impairment and risk of damage!u Use the adjustment of the appliance door only for ensuring that the door seal of the pull-out compartment makes 100 percent contact with the appliance body. Do not use it for adjusting the kitchen unit door. A check can be made on tight door closure by placing a shining electric torch inside. Clockwise: for inclination of the door away from the appliance body at the top. Anticlockwise: for inclination of the door towards the appliance at the top and away from the appliance body at the bottom. u After having adjusted the inclination, re-tighten all the screws Fig. 22 4. 4. 1 Adjusting the door inclination 4. 4. 2 Aligning the position of the door Note u Always make the adjustment on both sides, left and right! Fig. [. . . ] (see Maintenance). * → The LED lighting is defective or the cover is damaged:* u Wait until the appliance reaches the required temperature 7 Malfunction Your appliance is designed and manufactured for a long life span and reliable operation. If a malfunction nonetheless occurs during operation, check whether it is due to a handling error. In this case you will have to be charged for the costs incurred, even during the warranty period. You may be able to rectify the following faults yourself: Appliance does not work. [. . . ]