User manual LIFESAVER LIF 3010 SMOKE ALARM

[. . . ] LIFESAVER MODEL LIF 3000 SMOKE ALARM LIF 3010 SMOKE ALARM IONISATION DESIGN USER MANUAL AUSTRALIAN ELECTRICAL AUTHORITY CS: 96262V IMPORTANT: READ ALL INSTRUCTIONS BEFORE INSTALLATION. NO USER REPLACEABLE PARTS INSIDE THIS SMOKE ALARM. Do not attempt to repair the smoke alarm yourself. SPECIFICATION ELECTRICAL RATING: 240VAC 50Hz, 80mA per alarm, interconnectable up to 24 alarms. WARNING: THIS SMOKE ALARM MUST ONLY BE WIRED TO A 240VAC 50Hz SINE WAVE CURRENT SUPPLY. [. . . ] Test alarm weekly to assure proper operation. If no alarm sounds, check wiring, fuses or circuit breaker and make certain that alarm is connected to a continuous final sub-circuit. With interconnected units, activating the test button on one unit will cause all connected units to sound. Continuous chirping or erratic noise or low sound from an alarm may indicate a defective alarm. Return it for service. WARNING: Do not apply excessive force on the "TEST " and "HUSH " buttons, this may damage the smoke alarm and may void the warranty. WARNING: Never use an open flame of any kind to test your alarm. You may damage the alarm or set fire to your home. The built in test switch enables testing of all electronic components and the horn. To accurately test the integrity of the sensing chamber use a smoke detector (aerosol) ® tester. We recommend using the LIFESAVER LT711 Smoke Detector Tester for this purpose. 7. 6 7. 6. 1 Maintenance: The smoke alarm is virtually maintenance free. However, under dusty or greasy conditions, a vacuum cleaner may be used to clean the exterior of unit (including slots on cover). DO NOT IMMERSE IN OR SPRAY WITH HOUSEHOLD CLEANERS. We recommend a periodic monthly inspection of the smoke alarm to ensure that it is free of dirt. 8. 8. 1. 0 8. 1. 1 8. 1. 2 8. 1. 3 8. 1. 4 BATTERY TEST We recommend a weekly battery test. Switch off mains power OR unhinge the smoke alarm from its base plate. The Green LED on the smoke alarm will be OFF. Test alarm by pressing on the Test Button for a few seconds. It the Red LED is ON, it should diminish within 5 minutes. After the battery test, return the alarm to normal operation. Switch on mains power OR hinge the smoke alarm back onto its base plate only when smoke alarm passes the above tests. The Green LED on the smoke alarm will come ON. 9. LIFESAVER MODEL LIF3010 WITH NC/NO RELAY If you have purchased and installed the LIF3010 smoke alarm with the NC/NO Relay, please note that the operation and features of this model smoke alarm is the same as the LIF3000. The LIF3010 smoke alarm has 7 terminals and they are colour coded. WARNING: THIS TERMINAL IS NOT ISOLATED FROM THE MAINS SUPPLY 9. 1 9. 1. 1 This seven terminal has a relay output (C, NC and NO): A relay output may have a power loading (See figure 9. 1). Figure 9. 1 WARNING: The loading power must be less than 5Ax250VAC/10Ax125VAC/10Ax30VDC The smoke alarms can be interconnected to a maximum of twenty-four pieces. (please see figure 9. 2) 9. 1. 2 Figure 9. 2 9. 1. 3 9. 1. 4 Test if smoke alarm is okay by operating remote test & hush plate connected to smoke alarm. LIFESAVER Model LIFTHC: CHIP FOR REMOTE TEST & HUSH OPERATION (see figure 9. 3 and figure 9. 4) Figure 9. 3 (top) 9. 1. 5 Figure 9. 4 (bottom) By inserting this LIFTHC chip into the smoke alarm as shown in the diagram, it will allow your smoke alarm to be wired to the remote test and hush plate (LIFTHP). If your smoke alarms are interconnected, you would require a LIFTHC chip for each smoke alarm. [. . . ] Don't return to your home until officials say that it is safe to do so. For additional information on fire safety, contact your local Fire Brigade. 15. 3 15. 4 15. 5 15. 6 16. 16. 1 16. 2 16. 3 16. 4 INSTALLER PLEASE NOTE: Before you connect the mains power, check wiring polarity. If alarm `chirps ' intermittently, this sound is due to the "HUSH " button having been activated. [. . . ]