User manual LIFT-MASTER 65 9213

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual LIFT-MASTER 65 9213. We hope that this LIFT-MASTER 65 9213 user guide will be useful to you.

Lastmanuals help download the user guide LIFT-MASTER 65 9213.

Download

Manual abstract: user guide LIFT-MASTER 65 9213

Detailed instructions for use are in the User's Guide.

 [. . . ] DUAL AUXILIARY TROLLEY MODIFICATION
For Use With Models J,  H and GH
WARNING
APPLICATION
This modification is available for model J,  H and GH operators. For 1/2 HP and lower side mount operators use #48 drive chain. For 3/4 HP and higher side mount operators use #41 drive chain. 

659213-XX

WARNINGXX is door height.  [. . . ] Determine which side of the door the operator will be mounted on and install the track with the double idler on that side at the center of the opening. Install the track assembly with the single idler on the other side of the center of the opening. Brace the tracks appropriately. 

CONNECT TRACKS
1. Determine the length of the shaft needed to couple the two tracks together and cut the shaft provided to that length. Slide two bearing assemblies on the end of the shaft. Install a 48B14 sprocket on each end of the shaft using the (2) 1/4" x 1-1/2" roll pin provided (Figure 1). Use a tape measure to set the slider assemblies the same distance from the wall. Couple the shaft between the two idler assemblies by butting the 14 tooth sprockets together and connect with a #40 chain and master link (Figure 2). FIGURE 1
48B14 Sprocket 1" Bore 1" Diameter Shaft Be Sure Shaft is Flush With Sprocket. Do Not Let Shaft Protrude Beyond Sprocket. 

NOTES: 1. Shipped with 1/2 HP and lower side mount operators. Shipped with 3/4 HP and higher side mount operators. VARIABLE PARTS DOORS DOORS DOORS DOORS PART # DESCRIPTION 12'-14'' 16'-20' 22'-24' TO 26' K75-10259 Track Spacer 0 2 4 6 80-10383 Key Ring 1-1/4" 0 2 2 2

Drill 1/4" Hole - Pin with 1/4"x1-1/2" Roll Pin

1

I N S TA L L AT I O N
INSTALL OPERATOR
1. Install the operator using the appropriate manual. Determine the length of shaft needed to connect the operator to the double idler assembly and cut the shaft provided to that length. Install the last 48B14 sprocket to one end of the extension shaft with the 1/4" x 1-1/2" roll pin provided (Figure 3).  [. . . ] Bearing assembly should be mounted as close to the (50B12) sprocket as possible to prevent shaft flex. Refer to owner's manual for instructions on reversing limits. 

GH,  H,  J Operator (With Reversed Limits Logic 3 Requires Removal of Jumper) Disconnect Bracket

01-12575E

© 2005,  The Chamberlain Group,  Inc. All Rights Reserved

Printed in Mexico [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE LIFT-MASTER 65 9213

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual LIFT-MASTER 65 9213 will begin.