User manual LIFT-MASTER CROWN JEWEL PROGRAMMING

[. . . ] ® The Chamberlain Group 845 Larch Ave. Elmhurst, IL 60125-1196 www. chamberlain. com Crown Jewel Telephone entry system 1 23 456 789 0# G UP CALL 1 23 456 789 0# G UP CALL Keypad Programming Manual Table of Contents Quick Reference Guide Programming Basics 2-3 4-5 Visitor Calls 18-20 Procedure for Programming . 19 Enable/Disable Pulse Dial Activation . 19 Visitor Calls to Other Tenants (Dialing Codes) . [. . . ] Enable/Disable Call Forwaring Mode: 0 = Disable Call Forwarding 1 = Enable Call Forwarding 2 = Enable Scheduled Call Forwarding 3. Press EXAMPLE: 1 2 3 Enables the Call Fowarding feature. IMPORTANT NOTES: If you make an error during an entry, press the asterisk key () to begin again. The pound key (#) MUST be used to SAVE the data at the end of each programming step. Time MUST be entered using a 24-Hour format (8:00 AM = 0800, 3:00 PM = 1500 etc. ) 2 Short Beeps: Programming input is valid 1 Long Beep: Input is not valid. PAGE 16 Setting the Call Forwarding Extension - 16 When the Call Forwarding feature is enabled, the Crown Jewel is able to dial an extension number (up to 6-digits). Enter the Extension Number (up to 6-digits) 3. Press EXAMPLE: 1 2 3 Sets the Call Forwarding Extension Number as 1234. Setting the Call Forwarding Extension Delay - 15 1. Enter Delay amount (0-59 seconds) (0 = Disables Extension dialing) 3. Press EXAMPLE: 1 2 3 Sets a pause of 30 seconds between the Call Forwarding number and the Call Forwarding Extension number. Set the Call Forwarding Schedule - 18 Program calls to be forward during specified times and days. 1. Enter Days of the Week (To add one or more days to the Time Zone/Segment, press the digit corresponding to the day) : 1 = Sunday 2 = Monday 3 = Tuesday 4 = Wednesday 5 = Thursday 6 = Friday 7 = Saturday 8 = Holiday 3. Enter Holiday Option 0 = No Schedule on Holidays 1 = Use Same Schedule on Holidays 2 = Use Schedule Number 8 when this day falls on a Programmed Holiday 6. Press EXAMPLE: 1 2 3 4 5 6 Enables the Call Forwarding Schedule to contact the Call Forwaring Number on Thursdays from 9:00 AM to 5:00 PM excluding Holidays. PAGE 17 Visitor Calls When a visitor contacts a resident with the Crown Jewel , the resident can preform various functions using their touch-tone phone. The default settings are as follows: KEYS ON RESIDENT'S TELEPHONE WXYZ Activates Relay #1 JKL Extends Talk Time Hang Up and Deny Access to the Visitor Activates Relay #2 ABC Toggles Between Visitor and Another Phone Call Change the Visitor Call Response Keys - 34 1. Enter key that will activate Relay #1 (0-9 or ) 3. Enter key that will activate Relay #2 (0-9 or ) 4. Enter key that will toggle Call Waiting (0-9 or ) 5. Enter key that will extend Talk Time (0-9 or ) 6. Enter key that will Hang Up and Deny Access to Visitor (0-9 or ) 7. Press EXAMPLE: 1 2 3 4 5 6 7 Changes the phone key that operates Relay #1 to "1", Relay #2 to "2", the phone key that toggles between calls to "6", "7" extends talk time and "8" hangs up and denies access to the visitor. NOTE: The asterisk key ( ) may be assigned to a specific phone key response, therefore, you will be UNABLE to cancel a command in this programming step. Set Visitor Call Ring Sound - 06 FACTORY SETTING: 2 (Double Ring) 1. Enter Ring Type (Single Ring [1] or Double Ring [2] 3. [. . . ] "# " or " #"); Programming use a combination of three keys (i. e. "# #" or " # ") 02 = To enter Direct Commands use " "; Programming use " " 03 = To enter Direct Commands use "##; Programming use "##" 04 = Resident will NOT be able to program from their telephone or use Direct Commands 1[N] = To enter Direct Commands use "[N]#"; Programming use "[N][N] ". ([N] = Any number (1-9) on the telephone keypad. ) 3. Press EXAMPLE: 1 2 3 Sets the Alternate Prefix to enter Direct Commands to "# " or " #"; and Programming to "# #" or " # ". Enable/Disable the No-Telco Mode- 33 No-Telco mode is used when a unit is NOT using a phone line. [. . . ]