User manual LIFT-MASTER DC2000

[. . . ] DC2000 Back-Up Installation SL3000ULTM & SL3000ULDMTM Step-by-Step DC2000 Installation STEP 1 Bolt the DC2000 plate and guard to the operator chassis. Adjustment is required in Step 3. for for SL3000ULTM models UL ® LISTED 4K55 CLASS I, II, III, IV STEP 2 A B C Bolt the DC2000 control unit to the plate. Connect the DC motor wires to the DC2000 control unit wires. [. . . ] (Open left or Open right) Select your mode of operation for the DC2000 unit. (Automatic open or Manual open) Permanently wire optional controls according to label on control unit. (See back page) Adjust the sensitivity for the reverse sensor. OFF ON CLASS I, II, III, IV ON C D B D A C A 1 2 NC NC 2 1 NO 3 COM NO 3 COM W4 J5 B BACK -B K DC-BACKUP SENSOR ALARM D POWER OVERLOAD A C SL3000ULTM & SL3000ULDMTM with Interlock Assembly Step-by-Step DC2000 Installation STEP 1 Bolt the DC2000 plate and guard to the operator chassis. Adjustment is required in Step 3. STEP 2 A B C Bolt the DC2000 control unit to the plate. Connect the DC motor wires to the DC2000 control unit wires. Red to Red and Black to Black. STEP 3 A B C A Remove interlock assembly from motor with 3 screws. Replace the existing belt with the new belt provided. Pull down the DC2000 Plate to tighten the belt tension. Tighten the plate bolts to secure the plate. Reattach interlock assembly. Brown Red Green B Yellow Orange Purple STEP 4 Unplug interlock wire from OmniControl board, cut the plug off and strip wires. Insert Red wire in J-20 socket 3 and Black wire into socket 4 of the DC2000. STEP 5 A B C D Remove the OmniControlTM board from the electrical box. Plug in the DC2000 harness into the DC2000 control unit. Feed the DC2000 harness through the bottom of the electrical box. Feed the green and purple wires to the limit box. D OFF Existing Belt A Interlock Assembly DC2000 Control Unit Plate Bolts Plate B A C DC Motor B A C C Guard 7 456 ON W4 C A 123 B Do not over tighten belt B SL3000ULTM Use 4L 370 Belt SL3000ULDMTM Use 4L 400 Belt Socket 3 & 4 STEP 6 A B C D Reinstall the OmniControlTM board and make sure that the green and purple wires do not get pinched by the board. Plug in the DC2000 harness in the DC-BackUp J5 slot on the OmniControlTM board. Connect the red wire from the DC2000 harness into the top slot of the audio alarm plug. [. . . ] (The gate can be closed by manual command) 115 Vac Power Failure 115 Vac Power On, OmniControl BoardTM Malfunction Turn the 115 Vac power off then push and Hold to operate gate Turn the 115 Vac power off then gate opens automatically 115 Vac Power On, Emergency Override Push and Hold to override the OmniControlTM Board Push and Hold to override the OmniControlTM Board EMERGENCY OVERRIDE If 115 Vac power is on, but the system has an electronic malfunction, the gate can be operated using the DC2000 system with ANY of these devices shown. Manual Mode Auto Mode Push and Hold to operate gate Gate automatically opens "Optional Manual One-Button" CLASS I, II, III, IV SENSOR ALARM DC-BACKUP "Optional Photocell Sensor" 12 VDC Push and "Hold" to Open Push again and "Hold" to Close POWER OVERLOAD Part # AOMRON12V Part # AEXITP OmniControlTM Board Sensor Connection Power Ground USE ONLY 12 VDC FAILSAFE PHOTOCELL SENSORS FOR THIS SAFETY OPTION Failsafe Photocell: If a photocell is not working or loses power or photo beam is blocked, then the photocell will stop all gate operation. 45 4 Power +12 VDC 6 "Optional Key Switch" 0 DC20 ness 0 Har DO NOT wire 115 Vac power to the DC2000 If the DC2000 is automatically opening the gate due to a power failure, any manual command such as "Manual One-Button", "Three Push Button", "Key Switch", "Photocell" or "Edge Sensor" will cancel the automatic mode of the DC2000. After such cancellation, the DC2000 will continue to operate in manual mode until 115 Vac power is restored. 1 6 345 2 7 4 5 OPEN CLOS E Socket 3 4 Part # A1KX Turn and "Hold" to Open Turn again and "Hold" to Close "Optional Three-Button" CENTER SAFETY EXIT Interlock Assembly OFF ON N. O. 3 4 Com N. O. SENSOR ALARM 2 1 4 4 Com DC-BACKUP W4 GBA MS LINK N. O. SENSORS Com SYSTEM ON TIMER 60 3 POWER OVERLOAD OPEN REVERSE SENSOR ALARM SENSOR 1 3 OFF OPEN LEFT ON OPEN RIGHT MADE IN USA "Optional Radio Receivers" Push and "Hold" a Button to operate 1 3 1 3 EXIT COMMAND PROCESSED CENTER SAFETY FIRE DEPT. STRIKE OPEN RADIO RECEIVER GATE LOCKED EXIT LOOP SAFETY LOOP CENTER LOOP RESET MOTOR OSE LOS CLOSE STOP 12 VDC Back-up Radio Receiver OmniControl Surge Suppressor P/N Q410 Patent Pending 11 12 13 + Class 2 Supply 24 Volts DC DO NOT remove existing wires from the audio alarm or secondary protection sensor. Part # 412HM 56 44 1 G B M/S Link A Center Loop Safety Loop Exit Loop Fire Dept Key Switch Strike Open Push Button Radio Receiver 2 3 4 Jumper P2: to Momentary (M) Jumper P3: to 12 Volt CAUTION Vac Black 120 White Neutral Green Ground J5 BACK -B CK J5 DC-BACKUP SENSOR ALARM CHASSIS GROUND Red Wire White Wire Audio Alarm Wires 11 13 11 12 Button Three: Optional Accessories Button Two: 1 Back-Up Operation (DC2000) ® Button One: Normal Gate Operation (OmniControlTM Board) 2 3 4 Part # 412HM Part # 973LM POWER OVERLOAD For Technical Support and Ordering Parts: 1-800-528-2806 Green and Purple wires wrap behind board to the limit switches 24 VDC radio receiver to be used by OmniControlTM Board DC2000 Harness 13 12 11 11 Push and "Hold" DC2000 Remote Button to Open Push again and "Hold" DC2000 Remote Button to Close ® Radio Receiver + Radio Receiver © 2004 The Chamberlain Group, Inc. All Rights Reserved 01-51128 845 Larch Avenue Elmhurst, Illinois 60126 TM www. chamberlain. com [. . . ]