User manual LIFT-MASTER FDC

[. . . ] LM PL C C OWNER'S MANUAL MODEL FDC ADVANCED LOGIC INDUSTRIAL DUTY FIRE DOOR OPERATOR US PATENT NO. 6, 014, 307 O N TR O LMPLC CONTROL WIRED L B2 Wiring 2 YEAR WARRANTY Serial # (located on electrical box cover) Installation Date Wiring Type NOT FOR RESIDENTIAL USE 41B6 LISTED DOOR OPERATOR SPECIFICATIONS DRIVE SYSTEM GEAR REDUCERS:. . . . . . . . . . . . . . . . . . . . Helical inline, oil bath permanently lubricated, non-vented. CONTINUOUS POWER RATING: 1/2 HP: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 ft-lbs/sec 1 HP: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 ft-lbs/sec RATIO: 1/2 Hp: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48. 8:1 1 Hp: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49. 8:1 OUTPUT SPEED 1/2 HP:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 rpm 1 HP: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 rpm OUTPUT TORQUE 1/2 HP:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 929 in-lbs. 1 HP: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1990 in-lbs. [. . . ] Adjust open limit nut so that door will stop in open position with the bottom of the door even with top of door opening. Adjust close limit nut so that actuator is engaged as door fully seats at the floor. Close) Limit Switch SPARE Limit Switch WARNING TO AVOID SERIOUS PERSONAL INJURY OR DEATH FROM ELECTROCUTION, DISCONNECT ELECTRIC POWER BEFORE MANUALLY MOVING LIMIT NUTS. If other problems persist, call our toll-free number for assistance - 1-800-528-2806 Actuator RPM Board (Shown as LEFT Hand Unit) Rotator Cup Depress Plate OPEN Limit Switch 7 CLOSE Limit Switch NOTICE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. INSTALLATION MODE The motor operator installs as a standard commercial operator with standard wiring functionalty. Once installation is completed and all alarm devices are connected, and tested, the operator is then switched (DIP switch 2) to Fire Door Mode. Upon completion of installation, the units functionality should be checked by activating the key test station. If for any reason your unit does not respond as described in this manual, check that you have read and followed all installation and operating instructions. If difficulties persist contact the Lift-Master technical hotline. 1-800-528-2806. WARNING IT IS THE END USERS SOLE RESPONSIBILITY TO CHECK THAT ALL SYSTEMS ARE INSTALLED AND FUNCTIONAL. THE MOTOR OPERATOR MUST BE SWITCHED TO THE "FIREDOOR" MODE TO ENABLE ALL ALARM, AND WARNING SYSTEMS. DIP SWITCH #2 MUST BE SWITCHED TO THE "ON" POSITION TO ENABLE THE "FIREDOOR" MODE. FAILURE TO DO SO, COULD RESULT IN LOSS OF LIFE AND PROPERTY. Alarm Inputs: Alarm Input #1: Used for electronic alarm devices such as smoke detection devices or similar alarm systems. This alarm will activate a motored closure of the door, and all sensing and control devices will remain active. It is imperative that the alarm signal contact is maintained for a time period greater than the alarm delay to close setting. If dip switch #1 is in the "OFF" position (10 seconds) the alarm system must supply a "DRY" contact signal to terminals J2-11 & J2-12 for a minimum of 12 seconds. Alarm Input #2: Used for the thermal sensors (electronic fusible links) or similar systems. state only) This alarm condition will activate a motored closure of the door, and all sensing devices and control stations will be rendered inactive. This alarm will override any other alarm condition or input. 8 INSTALL POWER WIRING & CONTROL STATION Before installing power wiring or control stations be sure to follow all specifications and warnings described below. Failure to do so may result in severe injury to persons and/or damage to operator. Do not install any wiring or attempt to run the operator without consulting the wiring diagram. [. . . ] allows them to jump position on retainer. Door `drifts' when motor shuts off. Operator does not shut off at full OPEN or at full CLOSE position. Sprocket on limit shaft loose or limit drive chain broken. [. . . ]