User manual LIFT-MASTER GT

[. . . ] LO OWNER'S MANUAL MODEL GT LOGIC CONTROL (VER. 2. 0) INDUSTRIAL DUTY DOOR OPERATOR L IC G C O N TR O L FACTORY SET C2 Wiring See pages 14 and 15 for other wiring configurations PATENT PENDING The Maintenance Alert System TM allows the installer to set an internal Maintenance Cycle Counter. An LED on the 3-button station will signal when the set number of cycles is reached or when the opener requires immediate service. 2 YEAR WARRANTY Serial # (located on electrical box cover) Installation Date NOT FOR RESIDENTIAL USE 41B6 LISTED DOOR OPERATOR Wiring Type Before attempting to install, operate or maintain the operator, you must read and fully understand this manual and follow all safety instructions. These instructions are intended to highlight certain safety related issues. [. . . ] Every device that causes the door to open, except a reversing device, activates the Timer To Close. Auxiliary controls can be connected to open input to activate the Timer To Close. If the Timer To Close has been activated, the open button and radio control can recycle the timer. The stop button will deactivate the timer until the next command input. The Timer to Close will function from the programmable mid-stop with this wiring type. (NOTE: Requires Optional self monitoring photo eyes to operate. ) FSTS Momentary button contact for open, close and stop. Radio controls allowing open, close and stop. The single button station opens the door to the full open limit bypassing the mid stop and activates the Timer To Close, putting the operator in TS mode until the door reaches the down limit, or is stopped in travel. At which time the operator enters the B2 mode. (NOTE: Requires Optional self monitoring photo eyes to operate. ) ON ON T 1 2 3 4 OFF ON ON FSTS 1 2 3 4 OFF ON ON C2 FAIL SAFE 1 2 3 4 C2 Failsafe 3 Button, 3 Button Radio Control Same functions as C2. Self Monitoring safety device must be installed to operate door. See Self Monitoring Safety Device Options below. OFF ON ON B2 FAIL SAFE 1 2 3 4 B2 Failsafe 3 Button, 1 Button, 1 & 3 Button Radio Control Same functions as B2. Self Monitoring safety device must be installed to operate door. See Self Monitoring Safety Device Options below. OFF ON ON D1 FAIL SAFE 1 2 3 4 D1 Failsafe 2 Button, 3 Button Radio Control Same functions as D1. Self Monitoring safety device must be installed to operate door. See Self Monitoring Safety Device Options below. OFF ON ON E2 Failsafe 2 Button, 3 Button Radio Control Same functions as E2. Self Monitoring safety device must be installed to operate door. See Self Monitoring Safety Device Options below. E2 FAIL SAFE 1 2 3 4 OFF SELF MONITORING SAFETY DEVICE OPTIONS To use the operator in any of the Failsafe wiring modes, or Timer To Close wiring modes (TS, T, FSTS), a LiftMaster self monitoring safety device must be installed. Recommended LiftMaster Self Monitoring Safety Devices: CPS-L NEMA 1 Direct Connect Eyes CPS-LN4 NEMA 4 Direct Connect Eyes NOTE: 1. External interlocks may be used with all functional modes. Auxiliary devices are any devices that have only dry contacts. Examples are: photocell, loop detector, pneumatic or electrical treadles, radio controls, one button stations, pull cords, etc. [. . . ] Motor bearings are rated for continuous operation. n Inspect and service whenever a malfunction is observed or suspected. n CAUTION: BEFORE SERVICING, ALWAYS DISCONNECT OPERATOR FROM POWER SUPPLY. HOW TO ORDER REPAIR PARTS OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION ARE AVAILABLE 6 DAYS A WEEK CALL OUR TOLL FREE NUMBER - 1-800-528-2806 MONDAY THROUGH FRIDAY 5 AM TO 6 PM (MST) SATURDAY 7 AM TO 3:30 PM (MST) WWW. LIFTMASTER. COM WHEN ORDERING REPAIR PARTS PLEASE SUPPLY THE FOLLOWING INFORMATION: PART NUMBER DESCRIPTION MODEL NUMBER 22 ILLUSTRATED PARTS ­ ELECTRICAL BOX S7 S1 S6 S5 S2 S8 S4 S9 11 5 L7 L3 L1 S3 L9 6 L8 L5 7 L8 L6 L2 4 8 9 L2 L6 L4 2 10 4 1 3 23 REPAIR PARTS KITS ­ ELECTRICAL BOX LOGIC CONTROL (VER. 2. 0) Below are replacement kits available for your operator. [. . . ]