User manual LIFT-MASTER H

[. . . ] Logic 3 OWNER'S MANUAL J H HJ INDUSTRIAL DUTY COMMERCIAL DOOR OPERATOR This Operator Features the Enhanced IN T ENA N C E M A E R T SYS T The Maintenance Alert SystemTM allows the installer to set an internal Maintenance Cycle Counter. The Logic 3 operator incorporates a self-diagnostic feature built into the (MAS) Maintenance Alert System LED. An LED on the 3-button station will signal when the set number of cycles/months is reached or when the operator requires immediate service. Radio Receiver Built on Board 2 YEAR WARRANTY 315MHz Serial # Box Installation Date NOT FOR RESIDENTIAL USE E PAT E N T P E N D I N G M A L TABLE OF CONTENTS SPECIFICATIONS Carton Inventory . . 21-22 PREPARATION Hand Chain Handing . [. . . ] Then press the corresponding button on the remote control. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote you use 1 channel of the 23 channels on the radio receiver. ) 3. To program the CLOSE button to a remote control press the CLOSE button on the logic board. The RADIO LED will flash and then stay on solid. Then press the corresponding button on the remote control. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote you use 1 channel of the 23 channels on the radio receiver. ) 4. To program the STOP button to a remote control press the STOP button on the logic board. The RADIO LED will flash and then stay on solid. Then press the corresponding button on the remote control. The RADIO LED on the logic board will flash, this confirms that the remote control has been programmed. (By programming the remote you use 1 channel of the 23 channels on the radio receiver. ) 5. After learning remote controls press the RADIO button on the logic board (LED will turn off). NOTE: If no activity within 30 seconds the radio will automatically exit programming mode. Ø14LGØ657­A Ø14GPØ657­A P4 R31 C3Ø D8 E1 C18 U7 D31 D7 R29 C11 D3Ø2 X1 U1 P1Ø C25 D6 D5 C17 D4 D1 OPEN D22 Open EDGE OPEN K3 POWER 24V AC 24V AC 14 13 D2Ø OLS D25 D19 J1 J3ØØ TIMER DEFEAT R8 D17 TIMER DEFEAT 12 CMN MAS 11 10 9 8 7 REV STD CONTACTOR/3 PH CLOSE Close MID D24 SINGLE PHASE MAS D28 SLS D16 D26 MOTOR DIRECTION D21 CLS D27 4 EYES D23 CLOSE Stop EYES D15 STOP D13 P7 MRT MID TIMER D22 D1 EDGE OPEN EDGE D2Ø RADIO 1 D36 2 3 TIMER ENABLE CLOSE OPEN D21 RELAY A CLOSE 6 C77 STOP RELAY B D35 D13 STOP C78 ® STOP T TS FSTS DIAG CMN 5 4 3 2 C73 E2 D1 C54 L1 C2 L5 B2 FAILSAFE S8 PROG SBC C71 P6 (B2 C2 D1 E2) NON FAILSAFE D14 SBC P1 F1 D34 1 19 PROGRAMMING MAINTENANCE ALERT SYSTEM (MAS) Feature: An internal cycle counter will activate a flashing LED on the 3-button control station when the preset number of cycles or months has elapsed (whichever occurs first). By default this feature will never activate. Logic 3. 0 operators incorporate a self diagnostic feature built into the MAS LED. In addition to indicating when routine maintenance is due, the MAS LED can be used to troubleshoot some problems with the operator. Benefit: The Maintenance Alert System (MAS) assists the installing dealer in setting up a routine maintenance program. Once programmed, the MAS notifies the end user (with a flashing LED on the 3-button station) when a preset number of cycles/months has elapsed and scheduled maintenance is due. The Maintenance Alert System (MAS) assists the installing dealer in setting up a routine maintenance program. Once programmed, the MAS notifies the end user (with a flashing LED on the 3-button station) when a preset number of cycles/months has elapsed and scheduled maintenance is due. [. . . ] 3. 0) For replacement of electrical box, motor or brake components be sure to match model number of your unit to kit number below to ensure proper voltage requirements. SERVICE KITS ITEM PART # DESCRIPTION K1 K72-14130-1 Limit shaft kit Complete with: Limit shaft, limit nuts, limit bearings, limit sprocket, interrupter cup, shim washers, compression ring, roll pin, and e-rings. K2 K72-12515-1 Limit switch kit Complete with: Limit nut retainer, switch plates, backup plate, depress plates, limit switches, standoffs, screws, and locknuts. *To order a complete electrical box kit, add a K- prefix to the model number of your operator. [. . . ]