User manual LIFT-MASTER HL410

[. . . ] Installation and Maintenance Manual Swing Gate Operator Model HL410-21 & HL410L-21 Doc 01-20230 Rev B 2 Contents Contents Parts & Components ____________________________________________ 3 Specifications & Capacities _______________________________________ 4 Safety Information ______________________________________________ 6 Installer _______________________________________________________________ 6 End User _______________________________________________________________ 7 General Wiring Information ______________________________________ 8 Wiring information _______________________________________________________ 8 Installation ___________________________________________________ 10 Step 1: Step 2: Step 3: Step 4: Gate Stops______________________________________________________ 10 Gate Brackets ___________________________________________________ 10 Optional Mounting _______________________________________________ 11 Mounting ______________________________________________________ 12 Primary Voltage Wiring ___________________________________________ 14 Control Wiring __________________________________________________ 15 Hydraulic Adjustments ____________________________________________ 16 Adjustments ____________________________________________________ 17 Rod Cover______________________________________________________ 18 Control Panel Layout ____________________________________________________ 13 Step 5: Step 6: Step 7: Step 8: Step 9: System Check-Out _____________________________________________ 19 Limited One-Year Warranty _______________________________________________ 19 Parts List ____________________________________________________ 20 Required Maintenance Services __________________________________ 21 Doc 01-20230 Rev B Parts & Components 3 Parts & Components Inspect the operator for possible shipping damage or shortage of parts. These do not include any accessories that were ordered separately. DESCRIPTION Model HL410-21 or HL410L-21 Drive Unit Front Mounting Bracket Rear Mounting Bracket Rod Cover Rear Mounting Pin C-Clip Front Mounting Clip Disconnect Key Gate Caution Plate (!) Troubleshooting Guide Controller (sold separately) (!!) Table 1 !Gate Caution Plates are to be installed on the gate in a position where they can be QUANTITY 1 1 1 1 1 1 1 1 2 1 1 easily seen. !! [. . . ] Serious injury could result from someone being hit by the gate. Use outward swing gates only in applications where the gate will open into secure area and where the person operating the gate has control of traffic in the path of the gate. Do not use the "Open Only" mode of the controller for an outward swing gate installation. Gate stops must be used at both the full open and close positions (see Step 1). Follow Step 2 for mounting of gate brackets. The difference being that the rear mounting point is 5" to the right of the hinge point instead of 5" to the left as shown in Step 2 (distance between mounting points is 27-1/2" instead of 371/2"). The piston rod should be fully retracted when the gate is in the closed position. The unit should be mounted with the gate in the closed position (see Step 4). Follow wiring for outward swing. LARGE PILLARS OR WALLS If the dimension from the centerline of the gate to the outer edge of the pillar or wall is 3-3/4" or less, you can notch out part of the pillar or wall (see Example A ­ Figure 4) as shown. If this dimension is larger than 3-3/4", then it will be necessary to notch out larger portion (see Example B ­ Figure 4) large enough to house the unit. The notch should be 5" to 8" high. Contact a LiftMaster dealer if your application does not fit these guidelines. OPTIONAL MOUNTING - NOTCH AS REQUIRED 01-20230F6 EXAMPLE A EXAMPLE B Figure 4 Doc 01-20230 Rev B 12 Installation Step 4: 1 2 Mounting Manually open the gate and attach the unit to the two (2) mounting brackets (see Figure 5 below). Manually open and close the gate a few times to ensure the mounting brackets and gate stops are positioned properly with no interference (the unit is shipped in the disconnect position to allow for this). Mount the controller in a convenient location, within reach of the unit's 4 ft. Make sure the cord is not stretched taut (it should have a slight amount of slack during the full cycle). For Master/Slave Option: Mount both units. Refer to the electrical diagram attached to the inside of the controller door for accessory wiring. Please install all safety devices necessary to make this installation as safe as possible. Control Wiring Terminal Strip 1 2 4 5 6 8 9 10 D1 D1 D2 D2 24 VAC. OPEN/CLOSE If the gate is closed, when activated, it will open. If the gate is open, when activated, if will close. If the gate is activated while closing, it will reverse to open. If the gate is activated while opening, it will reverse to close. OPEN ONLY If the gate is closed, when activated, it will open. [. . . ] 1 2 3 4 Make sure the unit fully opens and closes the gate properly. Check all controls that activate the gate to ensure they are working properly. It is extremely important that all safety devices be checked and double checked. Double check the manual operation features and pressure valves of the system. [. . . ]