User manual LIFT-MASTER HS670

[. . . ] CO NT RO LL ER GL BO AR D HEAVY DUTY HYDRAULIC SLIDE GATE OPERATOR MODEL HS670 2 YEAR WARRANTY Serial # ________________________ (located on electrical box cover) Installation Date __________________ MODEL HS670 IS FOR VEHICULAR PASSAGE GATES ONLY AND ARE NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE TABLE OF CONTENTS OPERATOR SPECIFICATIONS Carton Inventory . . 3 Operator Dimensions and Horsepower Chart . . 5 IMPORTANT NOTE · BEFORE attempting to install, operate or maintain the operator, you MUST read and fully understand this manual and follow all safety instructions. · DO NOT attempt repair or service of your commercial door and gate operator unless you are an Authorized Service Technician. OPERATOR WARNINGS Safety Installation Information . [. . . ] When two operators are connected in dual gate configuration accessories may be connected to either the master or second. MASTER OR STANDALONE GATE SETTING MASTER UNIT ON SECOND GATE SETTING MASTER UNIT ON S4 SECOND UNIT S4 SECOND UNIT FIGURE 1 TB12 TB11 SHIELDED CABLE (TWISTED PAIR) MINIMUM 18 GAUGE CONDUIT TB11 TB12 NOTES: · Do not run Master/Second communication wiring in the same conduit as the power and control wiring. · The Second unit will require a normally close stop circuit for proper system operation. · After Master/Second wiring has been completed and the S4 switch programmed, both units must have their power cycled to initiate proper Master/Second communication. · The motor learn function must be completed in stand alone mode prior to Master/Second wiring. Street t up err p Int Loo t up err p Int Loo HS 67 0 (Gate Conduit) 6' Complex or Parking Lot HS 67 0 18 PROGRAMMING PROGRAMMING THE RADIO RECEIVER SET SECURITY MODE The Universal Receiver can be used with up to 15 rolling code transmitters or passwords in HIGH security mode. Alternately, it can be used with up to 31 of any type transmitter in NORMAL security mode, including any combination of rolling code, billion code, or dip switch remotes. The jumper must be set at the HIGH position for the receiver to operate in HIGH security mode. It must be set at NORMAL position to operate at the NORMAL mode (Figure 1). When changing from NORMAL to HIGH security mode, any previous transmitter codes must be erased. Repeat Steps 2 and 3 in the Programming Section below to reprogram the receiver for each remote control transmitter in use. SET OUTPUT DURATION To prevent possible SERIOUS INJURY or DEATH from electrocution: · Be sure power is not connected BEFORE installing the receiver. To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door: · ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control transmitters. · Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. · ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. WARNING CAUTION FIGURE 1 Security Mode Terminals Jumper Security Mode Terminals Jumper WARNING To prevent possible SERIOUS INJURY or DEATH, the use of CONSTANT OPERATION on residential openers is PROHIBITED. WARNING WARNING HIGH SECURITY MODE NORMAL SECURITY MODE CAUTION For commercial applications, the receiver can be set for either constant or momentary closure on the output contacts. Use of constant closure is prohibited on residential garage door openers because it overrides the safety reversal devices. With the jumper in the "M" (Momentary) position, the contacts will close for 1/4 second regardless of the length of radio transmission. With the jumper in "C" (Constant) position, the contacts will stay closed as long as the radio continues transmitting (Figure 2). PROGRAMMING THE REMOTE TO THE RECEIVER 1. Pry open the front panel of receiver case with a coin or a screwdriver. Re-connect power to operator (Figure 3). Press and release the "learn" button on the receiver. [. . . ] warrants to the first retail purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of two years from the date of purchase. The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety. If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-2806, toll free, before dismantling this product. [. . . ]