User manual LIFT-MASTER STAR250-315

[. . . ] Jumper J2 must remain in the default position unless otherwise noted. THERE ARE NO OTHER SERVICEABLE PARTS. PATENTS PENDING WARNING Children operating or playing with a garage door /gate opener can injure themselves and others. The door/gate could operate unexpectedly causing serious injury or death. [. . . ] ALSO DISPLAYS USER PROMPTS AND MESSAGES. POWER INDICATOR SCROLLING DASHES ON DIGITAL DISPLAY WHEN AC OR DC POWER IS APPLIED TO THE UNIT. ANTENNA CONNECTION FOR CONNECTION TO THE DIRECT ANTENNA OR THE ANTENNA EXTENSION KIT. DELETE KEY USED TO DELETE A TRANSMITTER FROM THE SELECTED MEMORY LOCATION BLOCK KEY USED TO BLOCK THE RECEIVER FROM GRANTING ACCESS TO THE SELECTED TRANSMITTER. TRANSMITTER REMAINS IN MEMORY, AND MAY BE UNBLOCKED IN THE FUTURE. Add ADD KEY USED TO ENTER TRANSMITTERS AND ENTER RAPID LEARNTM MODE. Delete Block 1 4 7 * 2 5 8 0 3 6 9 # NUMERIC KEYPAD USED FOR PROGRAMMING AND QUERYING TRANSMITTER LOCATIONS. ALSO USED TO ENTER ADVANCED FUNCTIONS. STAR KEY USED TO ENTER ADVANCED FUNCTIONS: *, 1- LAST TRANSMITTER RECEIVED *, 2- NO. OF BLOCKED TRANSMITTER LOCATIONS *, 5- FIRST BLOCKED TRANSMITTER LOCATION *, 7- SOFTWARE VER. # *, 0- AUDIBLE DIAGNOSTICS OFF/ON POUND KEY USED AS AN ESC OR EXIT KEY FOR ALL FUNCTIONS OR MODES. PROGRAMMING THE STAR250 Rapid LearnTM- Add transmitter to next available location. AUTO 001 Add PRESS PRESS # PRESS TO EXIT aDD Adding Transmitter- Add transmitter to a specific location. AUTO 001 Add PRESS 002 2 023 3 234 4 PRESS # PRESS TO EXIT ENTER LOCATION (1-250) aDD Deleting a Transmitter- To delete a user. dEL dEL Delete PRESS 002 2 023 3 234 4 Delete PRESS TO CONFIRM END ENTER LOCATION (1-250) 2 PROGRAMMING THE STAR250 (CON'T) Blocking (Unblocking) a Transmitter- To block or unblock a user. bLc Block PRESS 002 2 023 3 234 4 Block PRESS TO CONFIRM bLc OR (UNBLOCK) END ENTER LOCATION (1-250) Un- bLc Duplicating Memory- Allows user to back up learned transmitter memory into the provided backup memory module. dup , PRESS SIMULTANEOUSLY Main Memory Module Backup Memory Module * 6 END ~6 SECONDS Note- To duplicate memory, plug memory module into back up slot and press *, 6. Once duplication is complete, remove the backup memory module and store in a separate location. Restoring Memory- To restore memory, simply place the duplicate memory module from the backup memory location in the main memory position. Advanced Functions Step 1. For advanced functions, press and hold the (*) key and a number key at the same time to select the corresponding advanced function. (See table at right for available functions. ) Press the `#' key to exit the function. *1 *2 *3 *4 *5 *6 *# 7 *0 Memory location of last transmitter received. 5 Next blocked location (Repeat to scroll). Duplicate memory- See Duplicating memory. Audible diagnostics OFF/ON (LED will be displayed when OFF) * If no transmitters are programmed into the STAR250, then (---) will be displayed. Audible Diagnostics Step 1. (LED will be displayed when OFF) Double Beep- Transmitter is valid & learned into STAR250 accompanied by transmitter location display. Slow Beep- Security+ Transmitter (Not learned in STAR250). Fast Beep- Billion Code Transmitter (Not learned in STAR250). No Beep- Transmitter not working. Keypad Sound Alerts Single Beep- Key Pressed. [. . . ] Verify transmitter is listed in compatible transmitters section 3. Replace transmitter battery Replace Main memory module Replace Backup memory module Cycle power. If unit exhibits this condition again after 2 minutes, contact Technical Service ELECTRICAL CONNECTIONS FOR STAR250 RECEIVER (Bottom) STAR250 COMPATIBLE TRANSMITTERS WALL BUTTON OPENER 1 Common 2 Relay 24 v Billion Code Transmitters G81-315LM Security+ Keypads G976-315LM TRANS PRIMARY Security+ Transmitters G970-315LG G971-315LM G972-315LM G973-315LM G974-315LM N. O. [. . . ]