User manual LIFT-MASTER SW425

[. . . ] OWNER'S MANUAL MODEL SW425 RESIDENTIAL SWING GATE OPERATOR 2 YEAR WARRANTY Serial # ________________________ (located on electrical box cover) Installation Date __________________ MODEL SW425 IS FOR USE ON VEHICULAR PASSAGE GATES ONLY AND IS NOT INTENDED FOR USE ON PEDESTRIAN PASSAGE GATES TABLE OF CONTENTS OPERATOR SPECIFICATIONS Carton Inventory . . 2 Operator Dimensions and Specifications . . 4-5 WARNING Mechanical OPERATOR WARNINGS UL325 Model Classifications . . 7 Suggested Entrapment Protection Device Locations . [. . . ] If the gate operator is a standard 115V model, run conduit from the 115V power source into the gate operator (Figure 1). The gate operator is provided with a 90 degree flexible conduit fitting for installations where the electrical box is relatively close. Because of the 90 degree fitting, it is generally easier to run the electrical wires through the flexible conduit before attaching the conduit. Wiring for other devices such as push buttons may also be run at this time either in the same conduit or in another. Figure 1 Conduit Holes Junction Box Flexible Conduit Conduit Fitting Make sure that wiring is employed as required by local codes. Figure 2 If not already done, run three 12 gauge wires (hot, neutral and ground) from the power source, through the conduit and into the gate operator (Figure 2). It is easier to run these wires back out of the large hole in the operator along with the three existing wires. This allows the connection to be made externally and then later inserted back into the operator through the large hole. Be sure to use wire nuts to secure these connection. Be sure that the grounding wire is connected to a good earth ground. Make the connections as follows: · Black to (hot) · White to (neutral) · Green to (ground) Line Neutral Ground Wire Nut 13 WIRING BATTERY RUN INSTALLATION If the gate operator is a battery run model, it is packaged from the factory with the battery disconnected. Connect the red wire to the positive battery terminal and the black wire to the negative battery terminal (Figure 3). There are wires provided for connecting the low voltage burial cable from the transformer to the gate operator. Be sure that the positive and negative match the positive and negative of the charger. Connect the other end of the burial cable from the operator to the transformer. Be sure to match the positive and negative terminals of the charger to the positive and negative terminals of the battery (Figure 4). Once the connections are made, plug the charger into a 115V outlet. If possible, it is desirable to locate the charger out of the weather. Be sure the battery has been properly charged before putting into operation. Figure 3 Negative Terminal Batteries SOLAR POWERED INSTALLATION If the gate operator is solar powered, no power will need to be run into the machine. The ends of the wires are provided with connectors which can simply be plugged in (Figure 5). Turn the panel so that it will get maximum sunlight during the day. If necessary the panel may be mounted away from the gate operator to get it out of the shade and into more consistent sunlight. [. . . ] Primary and Secondary Arm Kit Complete with: Primary arms, swivel, hex bolts, locknut, hex nuts, flatwashers, lockwashers, pipes, coupling and disconnect arm. Radio Kit Complete with: Radio, antenna, cable extension kit, screws, flatwashers, lockwashers and nuts. ITEM 1 2 3 4 5 6 7 8 9 10 11 12 INDIVIDUAL PARTS PART # 13-40067 10-40137 20-40155 21-40074 23-40161 25-40083 25-40152 29-40071 29-40089 29-40095 29-NP712 K79-40056 K79-40098 DESCRIPTION Limit Nut Gate Bracket Motor, 12Vdc Transformer Limit Switch, SPDT Overload, 1. 5 amp Motor Breaker, 7 amp Resistor, 1 Ohm, 25W, Ohmite Sonalert Piezo Alarm Charger, Battery 12V . 5A Dual Stg Battery, 12V 7AH Control Board - Full System Control Board - Solar K2 K74-40084 K3 K74-40045 K4 K74-40065 K5 K72-40146 K6 K74-40141 K7 K74-40031 K8 K74-40151 K9 K75-40132 K10 K74-19916 26 I L L U S T R AT E D PA R T S K9 2 K5 K8 5 8 4 K1 3 K10 K2 K4 12 K3 K6 10 K7 6 9 11 27 WARRANTY POLICY LIFTMASTER® TWO YEAR LIMITED WARRANTY The Chamberlain Group, Inc. warrants to the first retail purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of two years from the date of purchase. [. . . ]