User manual LINKSYS WAG120N

[. . . ] Non-Wireless Equipment (ADSL Modems/Gateways) The following standards were applied during the assessment of the product against the requirements of the Directive 1999/5/EC: •• EMC: EN 55 022 and EN 55 024 •• Safety: EN 60950-1 CE Marking For the Linksys products such as the ADSL modems/ gateways, the following CE mark is added to the equipment. Denmark In Denmark, the band 5150 - 5350 MHz is also allowed for outdoor usage. Wireless Equipment (Wireless-N/G/A/B Products) The following standards were applied during the assessment of the product against the requirements of the Directive 1999/5/EC: •• Radio: EN 300 328 and/or EN 301 893 as applicable •• EMC: EN 301 489-1, EN 301 489-17 •• Safety: EN 60950-1 and either EN 50385 or EN 50371 I Danmark må frekvensbåndet 5150 - 5350 også anvendes udendørs. France For 2, 4 GHz, the product should not be used outdoors in the band 2454 - 2483, 5 MHz. [. . . ] For nærmere informasjon om håndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon for avfall eller butikken der du kjøpte produktet. Com/international Modem routeur ADSL2+ sans fil 21 Annexe C Réglementation Cisco-Linksys ADSL2+ Devices on Long Lines ADSL2+ devices may not achieve the type of “high speed” operation expected when attached to a line that is longer than intended by the ITU-T Rec. If the device is installed in such conditions and does not give the expected “download” performance, then do not refer the matter to the Telecom Fault Service or ADSL Helpdesk. Australia The following information applies if you use the product within Australia. Safety Notice WARNING: To ensure compliance with exposure limits to radiofrequency fields, the antenna of the device should be no closer than 20 cm from the body during use. New Zealand The following information applies if you use the product within New Zealand. United States of America The following information applies if you use the product within the United States of America. Telepermit Statement The cabling between the phone port and the phone shall not exceed 100 metres. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •• Reorient or relocate the receiving antenna •• Increase the separation between the equipment or PTC200 General Warning The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom’s network services. Wireless Connectivity Security on Cisco-Linksys ADSL2+ Devices Setting up the security of the wireless connection associated with ADSL2+ device is the user’s responsibility. Telecom will take no responsibility for charges made to user’s accounts due to poorly organized wireless security allowing unknown users to connect to the Internet via this device. Do not complain to the Telecom Fault Service or Jetstream Helpdesk should this occur. Devices •• Connect the equipment to an outlet other than the receiver’s General Warning for Cisco-Linksys ADSL2+ Devices and ADSL2+ Capability This device has been tested and found suitable to connect to the Telecom ADSL2+ capability. This indicates only that Telecom has accepted that this device complies with the spectrum management plan for ADSL2+ on copper cable and with simple voiceband compatibility tests included in PTC273. [. . . ] the required antenna impedance is 50 ohms. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the EIRP is not more than required for successful communication. Wireless Disclaimer The maximum performance for wireless is derived from IEEE Standard 802. Actual performance can vary, including lower wireless network capacity, data throughput rate, range and coverage. [. . . ]