User manual LISTAESCAN CONTROL STATION ASSEMBLY INSTRUCTIONS

[. . . ] Assembling the Control Station Lista offers three types of Control Stations: Basic Control Station Control Station with Owner-Configured Drawers Control Station with Preconfigured Drawers The Control Station is available in two sizes: 2000mm and 2200mm. All Control Stations feature a locking Tambour Door. Depending on your security requirements, the Tambour Door can be locked at the desktop, or at the base of the Control Station. Assembly Suggestions Assembly instructions are identical for all types of Control Stations, unless otherwise indicated. Assembling the Control Station requires two people to attach the Universal Panels to the Vertical Side Frames, and to attach the Rear Panels. Figure 1 Types of Control Stations Basic Control Station Control Station with Owner-Configured Drawers Control Station with Preconfigured Drawers 1 Assembling the Control Station Frame This chapter provides instructions for assembling the frame of the Basic Control Station, and the Control Station with owner- or pre-configured drawers. [. . . ] Follow the instructions below to install the cabinet locking system. For Control Stations with pre-configured drawers, the drawers occupy 750mm of drawer points. Lista marks these heights with oblong-shaped notches on the front and back of each Vertical Side Frame. Each U-Track occupies three notches (75mm). The following table provides information on installing the U-Tracks. Drawer Height 2" (75mm) 3" (100mm) 4" (125mm) 5" (150mm) 11" (300mm) Install U-Track with this many open notches showing Top (covering first 3 open notches) one open notch showing 2 open notches showing 3 open notches showing 14 open notches showing Inserting the U-Tracks Step 1 Action (Refer to Figure 5) Caution: Wear gloves when handling the U-Tracks as their edges can be quite sharp. Hold the U-Track so that the tabs are in front and the prongs are in back. Each U-Track is stamped with an L (for Left) or an R (Right). Install each U-Track (as indicated above for pre-configured drawers) onto the insides of the Left Vertical Side Frame and Intermediate Vertical Side Frame. Make sure the tabs in front are firmly seated. Press a Safety Clip into the front rectangular notch of each U-Track to lock them firmly into place. 2 Note: If the Safety Clip does not seem to fit properly, it indicates that the U-Track is not firmly seated in its mounting slot. If you need to remove the Safety Clip, gently tap it with a screwdriver. Inserting the Cabinet Lock System Step 1 2 Action (Refer to Figure 6 through Figure 9) Position the Lock Channel into the back of the Floor and Left Center Universal Panels. Note: The Plastic Pivot of the Lock Channel should be at the top. Viewing the cabinet area from the front, loosely secure the Mounting Brackets to the rightmost hole patterns (2nd and 4th) in the Center and Floor Universal Panels using " - 20 x " Round Head screws and " - 20 Kep nuts. Insert the screws through the Mounting Brackets and into the Panels and secure with Kep nuts. Install the 3rd and 4th drawers by holding the drawer at an angle with the Suspension Frame up to prevent it from sliding, and insert the Suspension Frame into the U-Track. Installing only the 3rd and 4th drawers provides enough room to access the Lock Channel Mounting Brackets. The Camplates on the back of the drawers should fit snugly around the Lock Channel. Note: Do not fully tighten the Mounting Bracket screws at this time. 3 Note: Occasionally, the drawer's Camplates may interfere with the Shuttle of the Lock system. If this happens, loosen the Mounting Bracket screws and slide the Lock Channel up or down until the Camplate no longer touches the Shuttle. 4 5 6 7 8 6 Insert the Aluminum Rod into the Rotor of the Lock Channel. [. . . ] Insert 5/16" - 1" Hex Head Lag bolts and 5/16" washers up through the corners of the Center Panel(s) and into the pre-drilled holes in the Maple Top (#43). 2 10 Figure 12 Bookcase(s), Peg-Board, Maple Top Installation 11 Attaching the Tambour Door Assembling the Endstops and Attaching the Tambour Door Step 1 2 Action (Refer to Figure 13) Place the pre-assembled door unit (#12) on its back (12" - 16" from the front of the unit) on top of the predrilled Top Universal Panel (#7). (It will be positioned properly later in this procedure. ) Assemble the Left and Right Endstops (#15) using Anchor Brackets (#59) secured with M6 x 16 Hex Head bolts. Insert the Left Endstop (#15) into the rear portion of the Left Door Track (the L shape faces the front of the unit). Insert the Right Endstop (#15) into the rear portion of the Right Door Track. [. . . ]