User manual LISTAESCAN HEAVY DUTY ROLL-OUT TRAY

[. . . ] FOLLOW LOCAL REGULATIONS AND BUILDING CODES TO DETERMINE THE PROPER METHOD OF ANCHORING. Assembly Instructions for Heavy Duty Roll-Out Trays Hardware included (per tray): SAFETY PRECAUTIONS CABINETS AND STORAGE WALL SECTIONS MUST BE SECURED TO FLOOR AND/OR WALL PRIOR TO INSTALLING HEAVY DUTY ROLL-OUT TRAY. CABINETS AND STORAGE WALL SECTIONS MUST BE ANCHORED IF THEY ARE LOCATED IN AN AREA THAT IS PRONE TO SEISMIC ACTIVITY. GLOVES MUST BE WORN DURING INSTALLATION OF THESE COMPONENTS. DO NOT FULLY EXTEND ROLLOUT TRAY UNTIL ALL ASSEMBLY STEPS ARE COMPLETE. [. . . ] · Lift the front portion of the extension track, , or . . . over the front bearing of the outside support track , or . · Repeat the last 2 steps for the other extension track. · Insert galvanized retainer bracket into the first slot in the front vertical side frame directly above the outside support bracket and push the top tab into the second slot. Hold the bracket in place with one hand and insert a 1/4-20 x 3/4" socket cap screw through the hole of the outside support bracket and secure with a 3/16" allen wrench into the retainer bracket. · Extend right , , and left extension tracks . . . · Lista recommends removing tray inserts from the tray before proceeding with the following steps. Removing tray inserts will make it easier to install the tray. Two people may be required to install the trays into the Storage Wall sections. Hardware Illustrations figure 1 1/4­20 x 3/4" socket cap screw with galvanized retainer bracket figure 2 5/16­18 x 1/2" socket cap screw with serrated washer Page 2 Parts List (Quantities) · , , , . . . Roll-out Tray (1) Right Outside Support Track (1) Left Outside Support Track (1) Right Extension Track (1) Left Extension Track (1) Galvanized Tray Inserts (3 for shallow depth models or 4 standard models) 1/4­20 x 3/4" socket head screw, retainer brackets (2 sets) ^ 5/16­18 x 1/2" socket head screw & washers (2) End cap and IDL (1 of each) S Handle paper label and plastic cover (1 set) tongues ^ . . . ^ , , , · S Figure 3 Vertical Side Frame min. distance from top edge of bottom universal panel 2" (50 mm) or two open slots Bottom Universal Panel Figure 4 cut-out in outside support track Figure 5 Page 3 (continued) IMPORTANT: Be sure to install socket cap screw before using roll-out tray. · Grasp tray · and slide rear left tray bearing behind front bearing of left extension track . . . . Slide tray up as far as you can and push tray into left extension track approximately 3-5". · Align right extension track , , with the right side of tray bearing and slide tray upwards behind bearing as far as you can. · Push the tray assembly in until it is fully engaged. · Tray should roll smoothly in tracks. CAUTION Be careful not to fully extend the tray until all assembly steps are complete. The tray could disengage from the track and cause injuries. · Be sure that rear back panel of tray · is pushed in past the hole in extension track with pem nut. Insert 5/16" socket cap screw ^ and bowed serrated security washer into pem nut in left and right extension tracks , , and . . . . [. . . ] You can use self-drilling/self-tapping hex head washer screws #12 x 3/4" (i. e. · If holes are present, attach the IDL profile to the vertical side frame with holes pre-punched along the front post. This should be on the same side that the IDL will be installed (See Figure 7). · Secure the IDL profile with 1/4-20 x 5/8" hex head bolts and nuts. [. . . ]