User manual LISTAESCAN OVERHEAD CABINET WALL MOUNTING INSTRUCTIONS

[. . . ] (fig 3 & 3a) 7 If pilot holes are required, use the upper mounting bracket as a template. Mark the locations on the wall where the bolts are to be inserted. 8 Drill the required holes 9 Re-Level, re-square and secure the upper mounting bracket to the wall. (figure 3 & 3A) 10 Attach the four mounting blocks to the cabinet, using the ¼-20 socket bolts provided (figure 4 & 4A). [. . . ] 5 Install the remaining lower and upper mounting brackets as shown in fig 6. 6 Before the last mounting bracket is installed, attach the second filler channel as shown if fig 6 7 Level, square and secure the final mounting bracket to the wall. 8 Follow steps 10 thru 14 on page 2 to install the cabinets. Figure 6 Note: Install second Filler Channel before installing last Mounting Bracket . FLUSH WALL MOUNTING without MOUNTING BRACKETS TOOLS NEEDED FOR INSTALLATION · · · · Drill Level Tape Measure Ratchet Wrench Figure 7 COMPONENTS NEEDED FOR INSTALLATION · Hardware to mount cabinet to wall (Not Provided by Lista) INSTALLATION INSTRUCTIONS 1 Open the Cabinet 2 Remove the Adjustable Shelf (Ref. Adjustable Shelf Removal Instructions) 3 Remove the bottom shelf 4 Bolt the cabinet to the wall through the four obround holes provided. The obround holes are Ø7. 2 x 10. 0 mm. (Figure 7) Note: Make sure the cabinet is level before it is bolted to the wall. 5 Reinsert the bottom shelf 6 Reinsert the adjustable shelf (Ref. Adjustable Shelf Reinstallation Instructions) obround holes for flush mounting Page 4 Installation and Use Instructions for Frame Mounted Overhead Cabinets TOOLS NEEDED FOR INSTALLATION · · · · · Drill & Drill Bits Ratchet Wrench for mounting hardware 3 /1 " Allen Wrench 6 Philips Head Screwdriver Level MOUNTING FRAME ASSEMBLY TO A SINGLE BASE CABINET (See Figure 8) 1 Drill four (4) 3/ 8" diameter holes into the rear of the cabinet as shown in Figure 8. 2 Follow Steps 5 through 12 below. COMPONENTS NEEDED FOR INSTALLATION Upper Support Posts (2) Base Posts (2) Upper Mounting Rail (1) Lower Mounting Rail (1) Mounting Blocks (4 per cabinet) Rear Panel (1) (if ordered) 5/ 16"­18 x 3½" Bolts, nuts and washers (4 sets) ¼­20 x 5/8 hex head bolts and ¼ lock washers (4 sets) " ¼­20 x ½" Socket Cap Screws (4 per post) ¼­20 x ¾" Socket Cap Screws and lock washers (4 per cabinet) #10­24 x ½" Sheet Metal Screws (2 per cabinet) MOUNTING FRAME ASSEMBLY ACROSS MULTIPLE BASE CABINETS 1 Locate the base cabinets that go on the extreme ends of the workcenter. Remove the drawers from those cabinets 2 Drill four 3 /8" diameter holes in the rear of the cabinets as shown in Figure 8. 3 Place the cabinet, with holes drilled along the right rear edge, on the extreme right of the workcenter. 4 Place the cabinet, with holes drilled along the left rear edge, on the extreme left of the workcenter. Note: If using a Steel Cover over the Base Cabinets, refer to the Steel Cover/Base Post Instructions on Page 7 before installing Base Posts. and Upper Support Posts into the base posts . SAFETY PRECAUTIONS READ INSTALLATION INSTRUCTIONS BEFORE STARTING INSTALLATION USE CAUTION WHEN HANDLING SHEET METAL PARTS, THE EDGES MAY BE SHARP THIS INSTALLATION WILL REQUIRE AT LEAST 2 PEOPLE DO NOT OVERLOAD FRAME BEYOND RATED LOAD CAPACITY. ­ 40 LBS/LINEAR FT PER SHELF ­ 150 LBS MAX FOR THE 78U ADJUSTABLE SHELF DO NOT PLACE OBJECTS ON TOP OF THE CABINETS YOU MUST INSTALL SAFETY SCREWS TO PREVENT OHC FROM LIFTING OR SLIDING OFF MOUNTING RAILS 6 Slide the Upper Support Posts 7 Bolt the sub assemblies together using the 5 /16 ­18 x 3½" long Bolts, 5/ 16" Nuts and 5/ 16" Flat Washers . Note: The sub assemblies created are left and right specific as identified in Figure 9. 8 Using the ¼-20 x 5/ 8" Hex Head Bolts and ¼" Lock Washers , bolt the left and right sub-assemblies to the Base Cabinets. (Figure 10) 9 Attach the Upper Mounting Rails and Lower Mounting Rails to the Upper Support Posts using the ¼-20 x ½" Socket Head Screws and ¼" Lock Washers . [. . . ] 2 Slide the Mounting Bracket away from the Cabinet Housing while pushing up on the Shelf. Figure 15 2mm Thick Washer/Spacer Adjustable Shelf Shelf Mounting Bracket TO RE-INSTALL ADJUSTABLE SHELF 1 Choose the desired height you want the Shelf to rest and insert the left Shelf Tabs into the rectangular slots at the desired height. Note: The shelf mounting bracket has to be under the shelf completely before the shelf assembly can be installed into the housing. (See Figure 15) 2 Slide the Support Bracket to the right until it locks into the right side slots. Slide mounting bracket in while pushing up on shelf to remove from housing. Page 7 CANOPY TOP INSTALLATION (See Figures 16 & 17) REQUIRED TOOL: Phillips Head Screwdriver 1 Using the #10­24 thread forming screws provided, attach the filler panel to the canopy. [. . . ]