User manual LISTAESCAN STORAGE WALL COMPONENTS INSTRUCTIONS

[. . . ] Chapter 1 Assembling the Lista Storage Wall Lista provides two types of standard Storage Walls: B251 and B255. The design, construction, assembly, and quality are identical for both types, however, B251 and B255 components cannot be interchanged. The B251 Storage Wall includes drawers with inside depth dimensions of 24" (610mm) and a frame depth of 27 ½" (700mm). The B255 Storage Wall includes drawers that are 18" deep (459mm) and a frame depth of 21 ¾" (553mm). Before Assembling the Storage Wall Before you begin assembling the Storage Wall, read through the assembly instructions to familiarize yourself with the order in which the parts are assembled. [. . . ] Install the Lower Rear Panel for the next section by overlapping it with the lower Rear Panel of the first section. 2 Note: To insert the Hex Head bolts easily into overlapped sections, use an awl or screwdriver to align the hole patterns of both panels. 3 After installing the Lower Rear Panels for the entire Storage Wall, place the Horizontal Support Brackets onto the tops of each Lower Rear Panel. Make sure the tabs of each Horizontal Support Bracket fit securely over the Lower Rear Panels. Attaching the Upper Rear Panels Step 1 Action (Refer to Figure 1-5) Position the first Upper Rear Panel by sliding it down and into the tabs of the Horizontal Support Bracket. Align the hole patterns of the Upper Rear Panel and Vertical Side Frames. Insert ¼-20 x 5/8" Hex Head bolts through the Upper Rear Panel and into the Vertical Side Frames. Insert the Upper Rear Panel for the next section by sliding it down and into the tabs of the Horizontal Support Bracket. Overlap the Upper Rear Panel with the existing Upper Rear Panel and secure with ¼ x 5/8" Hex Head bolts and ¼ - 20 Kep nuts. 2 Note: To insert the Hex Head bolts easily into overlapped sections, use an awl or screwdriver to align the hole patterns of both panels. 3 Attach the Upper Rear Panels for each section in the Storage Wall. Note: For back-to-back installations with a common Rear Panel, insert ¼-20 x 5/8" Hex Head bolts through the overlapping Upper and Lower Rear Panels and into the Vertical Side Frames. Secure with ¼ - 20 Kep nuts from inside the Storage Wall. Attaching the Sway Braces If your Storage Wall configuration includes Rear Panels instead of Sway Braces, refer to "Attaching Rear Panels. " Sway Braces must be installed in the first, last, and at least every fourth intermediate Storage Wall section. Secure with ¼-20 x 5/8" Hex Head bolts and nuts, as shown in Figure 1-6. For back-to-back Storage Walls, insert the ¼-20x5/8" Hex Head bolts through the bracing and into the Vertical Side Frame on the other side as shown in Figure 1-7. Secure with ¼ - 20 Kep nuts. 1-4 Figure 1-4 Rear Panels Figure 1-5 Rear Panels (Upper and Lower) Figure 1-6 Sway Braces Figure 1-7 Sway Braces (Back-to-Back Storage Walls) 1-5 Attaching Center Universal Panels If your Storage Wall includes a Center Panel, the clearance between the Bottom and Center Panels should be indicated on the drawing you received from your Lista Representative. It is important to install the Center Panel in the position indicated to allow for proper installation of drawers or roll-out trays. Note: If you are installing a Full-Height Locking System, do not install the Center Locking Panel at this time. This will be done after the Lock Channel is installed. Most Storage Walls are configured with either 900mm or 1350mm of drawer points. Lista marks these heights with oblongshaped notches on the front and back of each Vertical Side Frame. Position the Center Panel so that its bottom edge covers the top half of the appropriate notch unless indicated otherwise in your drawing. Refer to your unique Storage Wall drawing (supplied by Lista) to determine the height of the drawer points for your specific installation. For example, if your drawing indicates 750mm of drawers within an individual section, the drawers will occupy 30 total slots (30 x 25mm), each slot equaling 25mm. [. . . ] (Refer to Figure 1-15) Install two horizontal wire clips into the slots on the side of each shelf (one at the back and front, as shown). Note: You can also install Fill-In Strips on the top of the Vertical Side Frames. Horizontal Wire Clips are not necessary, simply place the Fill-In Strip between the two Vertical Side Frames. Installing Wide Span Beams Sets Lista offers three different lengths of Wide Span Beams for storage of items greater than the length of a single Storage Wall section. The lengths are: 56 ¼" for spanning two 36U sections; 80 5/16" for spanning two 54U sections, and 84 3/8" for spanning three 36U sections. Refer to the drawing provided by your Lista Representative to determine the appropriate length for installing Wide Span Beams on your Storage Wall. Step 1 2 Action (Refer to Figure 1-16 and Figure 1-17) Attach the four Anchoring Clips to each Vertical Side Frame (two in front, two in back). [. . . ]