User manual LISTAESCAN WORKBENCH ABOVE-WORKSURFACE ACCESSORIES ASSEMBLY INSTRUCTIONS

[. . . ] Note: If you are only attaching a Plain Backstop (with no Endstops or flanged edges), hold the Backstop flush with the bottom rear edge of the worksurface. Scribe pilot-holes and drill pilot holes 3/16" in diameter by 1" deep. Attach the Backstop using #14 x ¾" Phillips Pan Head screws. o Hardware List The following hardware is used for assembling the accessories shown in this manual. #14 x 3/4" Slotted Hex Head Screw 1/4" - 20 x 1/2" Phillips Head Round Screw w/ 1/4" - 20 Kep Nut #14 x 3/4" Phillips Pan Head Screw 5/16" - 18 x 3/4" Phillips Pan Head Screw 5/16" x 1-1/4" Hex Flange Screw , Attaching the Adjustable Riser Shelf Note: If you are mounting the Adjustable Riser Shelf onto a butcher block worksurface, the edge of the Foot Mounting Plates must be a minimum of 1" from the edge of the butcher block worksurface. You should have two riser shelf supports for shelves up to 84" in length. You should have 3 supports for shelves over 84" in length. [. . . ] 5 Depress both Snap Button , , on each side of the Foot Mounting Plate and adjust to the desired height. The shelf should not have any weight on it prior to adjusting. , , Item # · , , , . . . Components List Description Riser shelf (not shown) Foot mounting plate L Bracket Snap-Button 5/16" x 1-1/4" Hex Flange screws #14 x 3/4" hex head screw , . . . Adjustable Riser Shelf Support Assembly Attaching the Stationary Riser Shelf Lista provides two types of rear panels for the Stationary Riser Shelf: Partial and Full. Assembling the Stationary Riser Shelf with a Partial Rear Panel 1 Place the Riser Shelf · upside-down on worksurface. 2 Align the End Panels , over the ends of the Riser Shelf · and snap down into position. Rotate the assembly so that the back of the End Panels , are facing up. 3 Place the Partial Rear Panel with the tabs facing down, just below the Riser Shelf ·. Slide the Partial Rear Panel into position until the two holes at each end are aligned. Secure the Partial Rear Panel to the Riser Shelf · and End Panels , using ¼" - 20 x ½" Phillips Head Round screws and ¼" - 20 Kep nuts. Stationary Riser Shelf (Partial Rear Panel) Assembling the Stationary Riser Shelf with the Full Rear Panel 1 Lay the Full Rear Panel · down (with the flange facing up) on your worksurface. 2 Place the Side Panel , down on the Full Rear Panel · so that the bottom rectangular cutout on the End Panel , fits over the tab nearest the flange on the Full Rear Panel ·. Note: When placing the End Panels onto the Full Rear Panel, make sure you have the correct End Panel. The Flat-finished sides of the End Panels should face the outside. All notches and holes should face the back. 3 Rotate the End Panel , so that it is flush with the edge of the Full Rear Panel ·. Make sure the tabs of the Full Rear Panel · fit into the slots of the End Panel , . Repeat Steps 2 and 3 for the other End Panel , . 4 Upright the Full Rear Panel · with the End Panels , attached on your worksurface. 5 Place the Shelf over the End Panels , and align the shelf's connector brackets so that they slide down and snap into the channels in the End Panels , . Make sure the back of the shelf fits securely into the tabs on the Full Rear Panel ·. Attaching the Stationary Riser Shelf to the Workbench 1 Place the assembly onto the desired location of the worksurface. Scribe pilot hole locations through the two larger holes at the bottom of each bracket. 2 Move the assembly and drill pilot holes 3/16" in diameter by ½" deep. Stationary Riser Shelf (Full Rear Panel) , , Attaching the Instrument Riser Shelf If your purchased the Full Rear Panel option with the Instrument Riser Shelf, attach the Full Rear Panel first. Attaching the Full Rear Panel (Optional) 1 Position the Full Rear Panel · against the back of the worksurface so that the Tab , rests on the worksurface. [. . . ] Remove the Shelf and using a 3/16" drill bit, drill the pilot holes 3/16" in diameter by 1" deep for each. Place the Shelf onto the Shelf Supports , , so that the hole patterns are aligned. Secure the Shelf Supports , , to the Shelf using #14 x ¾" Slotted Hex Head screws. on each Shelf Support , , with #10 - 24 x ¼" Phillips Head Round screws. [. . . ]