User manual LORUS Y182

[. . . ] Pull out Crown 1 to the second click when the small second hand is at the 12 o'clock position. The small second hand stops on the spot. Turn Crown 1 to set the hour and minute hands to the desired time. Push Crown 1 back in to the normal position in accordance with a time signal. [. . . ] They move quickly if the button is kept pressed. Push Crown 2 back in to the normal position. Note: If Crown 2 is pulled out to the first click within one minute after being pushed back in to t h e nor m a l p o s i t i o n , t he alar m s o unds . Alarm engagement/disengagement q To engage the alarm, pull out Crown 2 to the first click. Crown 2 Alarm hands indicate the designated alarm time. * The alarm rings at the designated time for 20 seconds. To stop it manually, press any one of the buttons, or push Crown 2 back in to the normal position. q To disengage the alarm, push Crown 2 back in to the normal position. Crown 2 Alarm hands indicate the current time. Note: If Crown 2 is pulled out to the second click, the designated alarm time is canceled with a beep. * In that case, set the alarm hands to the time indicated by the center hands again, push Crown 2 back in to the normal position, and then, pull it out to the first click and set the desired alarm time again. * However, if Crown 2 is pushed back in to the normal position before the warning beep stops, the designated alarm time will not be canceled. s ADJUSTING THE STOPWATCH HAND POSITION s HOW TO USE THE STOPWATCH · The stopwatch can measure up to 30 minutes in 1/5 second increments. · After 30 minutes, it will start counting again fron "0" repeatedly up to 6 hours. Stopwatch minute hand · If the stopwatch hands will not return to the "0" position when the stopwatch is reset or when the battery is replaced with a new one, follow the procedure below to reset the hands. Stopwatch 1 / 5 -s e c o n d hand Stopwatch minute hand B A B A Crown 1 Second click Stopwatch 1/5-second hand 6 Before using the stopwatch, be sure to check that Crowns 1 and 2 are set at the normal position, and press button "B" to reset the stopwatch hands to "0" position. Stopwatch operation Standard measurement 1. P r e s s b u t t o n " A " r e p e a t e d l y t o r e s e t t h e stopwatch minute hand to the "0" position. Press button "B" repeatedly to reset the stopwatch 1/5-second hand to the "0" position. * The hands move quickly if the respective buttons are kept pressed. Push Crown 1 back in to the normal position. * After adjusting the hand position, set the time. A Start A Stop B Reset s RESETTING THE BUIT-IN IC · In case any of the hands should move improperly, follow the procedure below to adjust the hand movement. B Accumulated elapsed time measurement A Crown 1 Second click A Start A Stop A Restart A Stop B Reset * Restart and stop of stopwatch can be repeated by pressing button "A". Split time measurement A Start B Split B Split release A Stop B Reset 1. Press buttons "A" and "B" simultaneously 3. Push Crown 1 back in to the normal position. * Before using the watch again, be sure to adjust the position of the stopwatch hands and set the time and alarm. * Measurement and release of split time can be repeated by pressing button "B". s LUMIBRITE WATCH (dial, hands, buttons, case, bezel, strap, etc. ) Measurement of two competitors 6 If your watch is a LORUS LUMIBRITE watch, it has following features. A Start B A B B LORUS LUMIBRITE watches absorb and store light energy from natural and artificial light sources and emit light in the dark. They are made of environmentally friendly material, and therefore, are harmless to human beings and the environment. · With a full charge, LORUS LUMIBRITE watches glow in the dark hours longer than conventional luminous watches of this type. If exposed to a light of more than 500 lux (i. e. , the brightness of a typical office) for approximately 10 minutes, or direct sunlight for 2 minutes, they will glow for hours. · Since LORUS LUMIBRITE watches emit the light they store, the brightness will decrease gradually over time. [. . . ] · Do not press the buttons or turn the crowns when the watch is wet. · If the watch is exposed to salt water, rinse it in fresh water and then wipe it thoroughly dry. Caution: Leather straps are not water resistant except so indicated, even if the watch head is water resistant. · ALLERGIC REACTION Because the case and band touch the skin directly, it is important to clean them regularly. [. . . ]