User manual LOWRANCE EP-15 FLUID LEVEL

[. . . ] The cable length from the connector to the smart module is 18 inches (46 cm) and from the smart module to the bare wires is 10 feet (3 meters). The smart module converts fluid level information received from the sending unit (fluid level arm or potentiometer) to the NMEA 2000 data format. This allows any digital gauge, sonar or GPS unit connected to the NMEA 2000 network to display the fluid level. The EP-15 sensor is most commonly used in fuel tanks, but it is designed to monitor fluid levels in almost any situation, including live wells, oil reservoirs, fresh water, gray water or black water tanks. [. . . ] Connect the negative black lead to the sending unit's negative connector. To be sure which connection is which, refer to the mounting instructions that came with the sending unit. Negative connector Positive connector Connect wire leads to fluid level sending unit. This is a typical sending unit mounting bracket. The center threaded post is + and the blade is ­ . Finally, connect the blue locking collar connector to the NMEA 2000 network. Route the sensor's cable connector to the T on the network backbone where you intend to attach it, and plug it in. Connecting to a NMEA 2000 Network A network bus is an installed and operational network cable (backbone) running the length of your boat, already connected to a power supply and properly terminated. Such a bus provides network connection nodes at various locations around your boat. This is similar to the telephone wiring in a house. If you pick up a phone in your living room, you can hear someone talking into the phone in the bedroom. Network Nodes A network bus is built of network nodes spread along a backbone. Network nodes are made by fitting T-shaped connectors into the backbone (using the sockets on the sides), and attaching a display unit or sensor at the bottom of the T. Using our telephone example, the T connectors are similar to telephone jacks. The backbone is like the phone wiring running through a house. 4 Phones in a house must be connected to each other to communicate, and in the same way only sensors and display units plugged into the NMEA network can share information. Connections found in the middle of the bus will have one or more of these T-shaped connectors with the backbone cables plugged into both sides. Connections at the end of a network will have the backbone plugged into one side, and a terminator plugged into the other, as shown in the following figure. Cable from sensor or display unit T connector LEI or Lowrance device needs an open T. Terminator at the very end of the bus Backbone cable (to rest of bus) NMEA 2000 network node located at the end of a NMEA 2000 bus. Adding a Network Node You can add a node anywhere along the network backbone where a connection already exists. This connection could be at the end of the network (between a T connector and a terminator), between two T connectors, between a T connector and a backbone extension cable, or between two extension cables. Wherever you want to add the new node, simply separate the sockets of the old connection and attach your new T connector between them. Lowrance or LEI device connects to new T connector. Add T-shaped connector to add device to bus. Attach terminator at end of bus. Existing network node Add a new device to a NMEA 2000 bus by attaching a T connector between two T connectors, between a T connector and the end terminator, or between two backbone extension cables. 5 If you want to add a node at the end of the line (as shown in the previous figure), remove the terminator from the very last connector, securely attach the new T connector, and then attach the terminator on the new connector. Either method will allow you to add a device. The "soft" T connector, shown above with a "hard" T connector, is another option for connecting devices in a NMEA 2000 network. [. . . ] Call toll-free: 800-661-3983 905-629-1614 (not toll-free) 8 a. m. Eastern Standard Time, M-F . . . outside Canada and the USA: Contact the dealer in the country where you purchased your unit. To locate a dealer near you, see the instructions in paragraph number 1 below. Accessory Ordering Information LEI Extras, Inc. is the accessory source for sonar and GPS products manufactured by Lowrance Electronics and Eagle Electronics. [. . . ]