User manual LOWRANCE LDT-3200

[. . . ] 988-0099-071 Digital Temperature Gauge Installation & Operation Instructions The LDT-3200 combines a temperature gauge, voltmeter and clock in one housing. It displays the temperature in either Fahrenheit °F or Celsius °C and may be set to rotate between four gauge displays or "pages. " The unit fits in a standard 2-1/8" (54 mm) hole used by most marine equipment manufacturers. The gauge and its temperature sensor are designed to show surface water temperature in a transom installation, but the sensor can be installed to monitor the temperature elsewhere, such as in a live well. LDT-3200 LDT-3200 temperature gauge. Mounting Preparations When installed, the gauge will cover an area on the dash 2-3/8" (60. 3 mm) in diameter. To mount the unit, first make sure there is at least 2-3/4" (70 mm) from the front of the dash to any obstruction behind the dash. [. . . ] When you install the gauge, the default time out duration is 5 seconds. You can modify the "TIMEOUT" setting by pressing MENU and using the up and 6 down keys to scroll through the main menu. When TIMEOUT appears in the center square -- like the illustration below -- press MENU. That will open the Timeout Menu, which has four settings: 3, 5, 7 and 10 seconds. To choose a setting, use the up and down keys and press MENU. Center square Timeout internal menu Timeout in the center square on the main menu (left) will take you to the Timeout menu. All items on the main menu (except Rev Video) will function in the same way. The Timeout menu (right). LDT 3200 Menus The unit has 11 menus. To access a menu, press MENU and use the up and down keys to scroll it into the center square, then press MENU. The menus are: AutoScroll; Backlight; Contrast; Options; Pages; Rev Video; Set Alarm; Set Time; Set Units; Timeout; and System Pages When you first start using the gauge it will display the Temperature page by default. But there are three other pages: the Voltmeter page, Dual Display page and Clock page. You can cycle through the pages manually or set them to be displayed at various intervals with the AutoScroll menu, discussed on page 8. To cycle through the pages manually, press the up or down keys. The Clock page is the only page not set for display by factory default. Temperature Page (left) and Voltmeter Page (right). 7 Dual Display Page (left) and Clock Page (right). To modify what pages will be displayed, press MENU and use the up and down keys until PAGES appears in the center square. Press MENU and use the up and down keys to move through the page options. Press MENU to check or uncheck the boxes next to the page category you want shown on the main display. After making your selection, the menu will time out and take you back to the main screen. Use the up and down keys to cycle through the four page displays, which are broken down in more detail below. Temperature Page The temperature sensor is mounted on the transom to monitor water temperature. Voltmeter Page The voltmeter displays the voltage. Dual Display Page The dual display page shows the temperature and the voltage, simultaneously. Clock Page The clock displays local time and is the only page category not included in the gauge display rotation by default. Setting the clock Press MENU, then use the up and down keys until SET TIME appears in the center square display, then press MENU again. [. . . ] THIS REPAIR, OR REPLACEMENT OR REFUND (AS JUST DESCRIBED) IS THE EXCLUSIVE REMEDY AVAILABLE TO YOU AGAINST US FOR ANY DEFECT, MALFUNCTION, OR NON-CONFORMITY CONCERNING THE PRODUCT OR FOR ANY LOSS OR DAMAGE RESULTING FROM ANY OTHER CAUSE WHATSOEVER. WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF ANY KIND. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty does NOT apply in the following circumstances: (1) when the product has been serviced or repaired by anyone other than us; (2) when the product has been connected, installed, combined, altered, adjusted, or handled in a manner other than according to the instructions furnished with the product; (3) when any serial number has been effaced, altered, or removed; or (4) when any defect, problem, loss, or damage has resulted from any accident, misuse, negligence, or carelessness, or from any failure to provide reasonable and necessary maintenance in accordance with the instructions of the owner's manual for the product. [. . . ]