User manual LOWRANCE X-45

[. . . ] X-45 INSTALLATION AND OPERATION INSTRUCTIONS 1 TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION - Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If you reach the maximum or minimum level, an warning tone sounds. To stop the chart, first clear any menu from the screen by pressing the ON/ CLEAR key. You can't stop the chart while a menu is displayed. The chart will freeze and the word "STOP" appears at the top right portion of the screen. To start the chart, press the up arrow key again. DISPLAY MODE The X-45 has three different screen modes. To change modes, press the MENU key until the "DISP MODE" (Display Mode) menu appears. Then press the up or down arrow keys until the desired mode number appears. The modes are as follows: CHT 1 (Chart #1) This is the default mode used when the X-45 is first turned on. Digital Depth Display On 15 CHT 2 (Chart #2) Same as Chart #1 plus digital surface water temperature display. CHT 3 (Chart #3) Same as Chart #1 plus a digital speed display. CHT 4 (Chart #4) This is the High Speed Scroll mode. All Digital Displays Off 16 DIG 1 (Digital #1) This is the first digital only screen. It shows the digital depth display at the top of the screen in very large numbers. The shallow and deep alarm settings are displayed beneath the digital depth. No chart shows on this screen. DIG 2 (Digital #2) The digital depth display shows at the top of this screen in very large digits. The digital temperature, speed, and log shows beneath the depth. The log starts counting when the X-45 is first turned on. When the X-45 is turned off, the log is reset to zero. ALARMS FISH ALARM The Fish Alarm sounds a tone when a fish symbol appears on the screen. To use the fish alarm, press the menu key until the "FISH ALARM" menu appears on the screen. Now press the up arrow key to turn the alarm on. Repeat the above steps to turn the fish alarm off. (Note: If the Fish ID feature is off, it will be turned on when you turn the fish alarm on. ) DEPTH ALARMS The depth alarms are triggered only by the bottom signal. No other echoes will activate these alarms. The depth alarms consist of a shallow and deep alarm. [. . . ] For proper testing, repair, and service, send a brief note with the product describing the problem. Be sure to include your name, return shipping address, and a daytime telephone number. Accessory Ordering Information To order accessories such as power cables or transducers, please contact: 1. Most quality dealers that handle marine electronic equipment should be able to assist you with these items. Consult your local telephone directory for listings. [. . . ]