User manual LUCID AUDIO GENIX696

[. . . ] USER'S GUIDES AESx4 CLKx6 GENx6 GENx6-96 D ig i ta l A ud i o Di s tr i bu ti o n P ro du ct s AESx4 i CLKx6 i GENx6 i Distribution Amplifier Audio Clock Distribution Amplifier Word/Superclock Generator Word/Superclock Generator 2 2 3 4 What `s Included in the Box Operator Safety Instructions AESx4 Distribution Amplifier WHAT'S INSIDE GENx6-96 i CLKx6 Audio Clock Distribution Amplifier 5 6 GENx6 Word/Superclock Generator GENx6-96 Word/Superclock Generator 7 8 9 Warranty Repair Services Declaration of Conformity Digital Audio Distribution Products User's Guide © 2001-2003 Lucid, a division of Symetrix, Inc. Part Number 53DIST-0C00 Revision: C01 The information in this guide is subject to change without notice. Lucid shall not be liable for technical or editorial errors or omissions contained herein; nor is it liable for incidental or consequential damages resulting from the furnishing, performance, or use of this material. Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a recommendation. [. . . ] The data can be either AES3 or AES11 (AES3 with no audio data). POWER: Supplied by external Lucid PS-3, PS-3E, or PS-3J. CLOCK OUTPUTS are coaxial BNC connectors with nominal impedance of 20 Ohms. Audio Clock Distribution Amplifier Jumper Settings J3 is used to select a word clock or super clock output format derived from the AES input signal. Specifications Electrical Input impedance: AES: 110 Ohms, Clock: 75 Ohms or Hi-Z, jumper selectable. Connectors AES INPUT: Balanced XLR WORD/SUPER CLOCK INPUT: BNC WORD/SUPER CLOCK OUTPUTS: 6 x BNC Power supply: External AC (Lucid PS-3, PS-3E, or PS-3J) using 7-pin DIN connector Physical 1/2 U Chassis (HxWxD):1. 72 in. x 8. 5 in. x 8 in. (4. 37 cm x 21. 59 cm x 20. 32 cm) Net Weight: 2. 5 lb. (1. 1 kg) AUDIO C LOC K DISTRIBUTIO N AMPLIFIER AES SIGNAL WORD/SUPER POWER WWW. LUCIDAUDIO. COM MANUFACTURED BY LUCID LYNNWOOD, WA, USA FABRIQUE PAR LUCID WORD/SUPER CLOCK OUTPUTS WORD/SUPER CLOCK INPUT AES INPUT CONNECT TO LUCID PS-3 OR PS-3E POWER SUPPLY ONLY THIS PRODUCT CONTAINS NO USER SERVICEABLE PARTS PAS DES ELEMENTS SERVIABLE PAR UTILISATEUR Page 4 of 9 USER'S GUIDES AESx4 CLKx6 GENx6 GENx6-96 Digital Audio Distribution Products GENx6 Description The GENx6 is used to distribute word clock and super clock, and also act as a generator device with its internal 2 clocks. It provides 6 clock outputs that may be internally generated to either word or super clock, or clocked from an external source. The device can also synthesize a word clock or super clock output derived from the word clock, super clock or AES input. Controls The GENx6 has 3 switches located on its front panel. · One 3-way toggle switch selects between internal 44. 1 kHz sample rate, internal 48 kHz sample rate, or external sample rate. · One 3-way toggle switch selects between the external sync sources of AES, WORD, or SUPER(256X) clocks. · One 2-way toggle switch determines if the output is WORD CLOCK (x1 sample rate) or SUPER CLOCK (256 x sample rate). LEDS 3 LOCK LEDs (a stack of 3): · The upper LOCK LED, labeled AES, indicates the AES input PLL has locked to an AES3 or AES11 input. · The middle LOCK LED, labeled WORD, indicates the wordclock PLL has locked to a word clock input. · The bottom LOCK LED, labeled SUPER(256X), indicates the input PLL has locked to a super clock input. POWER LED indicates AC power is present. Connectors WORD/SUPER CLOCK INPUT is a coaxial BNC female connector with nominal input impedance of 75 Ohms. Internal termination is provided with a jumper. AES INPUT is a 3-pin XLR connector with nominal input impedance of 110 Ohms. Internal termination is provided, as per the AES3 spec. The data can be either AES3 or AES11 (AES3 with Word/Superclock Generator no audio data). [. . . ] If you reside in the USA, then proceed as follows: 2. Have your serial number ready to give to the service representative. Pack the unit in its original packaging materials. Include your name, address, daytime telephone number, and a brief statement of the problem. [. . . ]