User manual LUMAGEN RADIANCE MINI-3D

[. . . ] RadianceMini-3DTM Video Processor Owner's Manual LEGAL NOTICES: TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT SHALL LUMAGEN, ITS SUPPLIERS, OR ITS DEALERS, BE HELD LIABLE FOR INJURY TO PERSONS OR PROPERTY, ANY LOST REVENUE, LOST PROFIT, SPECIAL, INCIDENTAL, INDIRECT, CONSEQUENCIAL, OR PUNITIVE DAMAGES, IMPAIRMENT OF OR DAMAGE TO OTHER GOODS, HOWEVER CAUSED REGARDLESS OF THE THEORY OF LIABILITY, RESULTING FROM THE USE OF, OR INABILITY TO USE, THIS PRODUCT, EVEN IF LUMAGEN, ITS SUPPLIERS, OR ITS DEALERS, HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. LUMAGEN SHALL NOT BE LIABLE FOR OMISSIONS OR ERRORS IN ITS DOCUMENTATION OR SOFTWARE. LUMAGEN RESERVES THE RIGHT TO MAKE CHANGES TO ITS PRODUCTS AND DOCUMENTATION WITHOUT NOTICE. Unless you are experienced in the installation and set-up of high-performance video electronics, we suggest you hire a professional home-theater specialist to do installation and configuration of this product. We recommend that you choose a professional who has been certified by the Imaging Science FoundationTM (ISF). [. . . ] The Radiance has both temporal and special noise reduction to help reduce the noise level these artifacts introduce into the image. Block artifact reduction is alos supported and can be useful with overly compressed video. The command is: MENU Input Video Setup [Resolution] Enhance Noise Red. OK Adaptive Contrast Adaptive Contrast varies the contrast based on the average level of the central 60% of the picture. When you adjust the contrast the effect is shown in a centered window for evaluation. The command format is: MENU Input Video Setup [Resolution] Enhance AdapContrast OK Copy Enhancement Settings You can copy the local enhancement settings to other resolutions and memories. The command is: MENU Input Video Setup [Resolution] Enhance Copy OK RadianceMini 22 rev 11/17/10 Section 5 ­ Video Configuration Miscellaneous Input Controls Deinterlacing Mode The default deinterlacing mode is "Auto. " This mode automatically switches between video and film deinterlacing and is best for mixed-mode sources that change between video and film. For sources that are known to be interlaced-video, choosing "Video" deinterlacing mode can improve image quality. For sources that are known to be film sources, choosing 'Film' deinterlacing mode can improve image quality. For 60Hz interlaced film sources the output must be one of 24, 48, 60, or 72 Hertz, and for 50Hz interlaced sources the output rate must be 50 Hertz. For "Film" mode, Sharpness, Noise Reduction and Adaptive Contrast settings are not available. The command is: MENU Input Video Setup [Resolution] Control Deint Mode (Auto, Video, Film) Inter Frame Motion Detection (IFMD) For deinterlacing video sources (not applicable for film) the IFDM control trades-off between minimizing combing artifacts (small values) verses maximizing detail (larger values) using the IFMD setting. This control is most effective with "Video" deinterlacing mode. The command is: MENU Input Video Setup [Resolution] Control Deint IFMD (0-15) Game Mode To minimize video processing latency when playing video games, turn "Game Mode" on. Typically game mode is enabled for a specific input memory that is then selected while playing games. For games that have a vertical rate that matches the Radiance output vertical rate, turning "Genlock" on can further minimize video latency. Game mode is not intended for video/film program material, such as television shows. The command is: MENU Input Video Setup [Resolution] Control Game Mode (On, Off) Genlock Genlock is used to minimize video delay, for 480i/1080i to 24Hz conversion, and to avoid an occasional dropped or repeated frame. It can slow down source and mode changes, so Lumagen recommends setting Genlock to `off' for cable and satellite settop boxes. The command is: MENU Input Video Setup [Resolution] Control Genlock (Auto, Disabled) Deinterlacing Field Flip Some source devices do not follow conventions for the order of video fields. This can be seen as excessive combing in the video. While generally not required, this command allows the input fields to be swapped so these out-of-spec sources can be properly deinterlaced. [. . . ] 2 lines, 30 characters per line, legal characters '' through 'z' (0x20 - 0x7a in hex), a carriage return or '{' can be used to terminate message. ASCII extended characters set solid block for use as a volume bar. Set zoom factor to M-- Where M can be 0-2 (or 0-7 if zoom is set for 5% steps) Set output aspect ratio to MMM for all input aspects--. Where the valid range is 110-250 which corresponds to 1. 10 to 2. 50. [. . . ]