User manual LUMAGEN RADIANCE XS

[. . . ] RadianceXS® Video Processor Owner's Manual Rev_112809 LEGAL NOTICES: TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT SHALL LUMAGEN, ITS SUPPLIERS, OR ITS DEALERS, BE HELD LIABLE FOR INJURY TO PERSONS OR PROPERTY, ANY LOST REVENUE, LOST PROFIT, SPECIAL, INCIDENTAL, INDIRECT, CONSEQUENCIAL, OR PUNITIVE DAMAGES, IMPAIRMENT OF OR DAMAGE TO OTHER GOODS, HOWEVER CAUSED REGARDLESS OF THE THEORY OF LIABILITY, RESULTING FROM THE USE OF, OR INABILITY TO USE, THIS PRODUCT, EVEN IF LUMAGEN, ITS SUPPLIERS, OR ITS DEALERS, HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. LUMAGEN SHALL NOT BE LIABLE FOR OMISSIONS OR ERRORS IN ITS DOCUMENTATION OR SOFTWARE. LUMAGEN RESERVES THE RIGHT TO MAKE CHANGES TO ITS PRODUCTS AND DOCUMENTATION WITHOUT NOTICE. Unless you are experienced in the installation and set-up of high-performance video electronics, we suggest you hire a professional home-theater specialist to do installation and configuration of this product. We recommend that you choose a professional who has been certified by the Imaging Science FoundationTM (ISF). [. . . ] Dither position sets the bit size of the pixel for dithering. Orientation controls the frame-to-frame randomization and can be fixed of dynamic. Masking can be turned on to clear the lowest bits after the dither. The command is: MENU Output Configs [Config] HDMI Format Dither Mask and Shrink The "mask" command allows you to "blank" the edges of the video image on the output without changing its position or size. The gray level of the mask is adjustable from black to white in sixteen steps. The mask covers the active video and the graybars. The "shrink" command allows you to adjust the image size to fit inside a screen masking system. The command is: MENU Output Configs [Config] Mask/Shrink (Mask, Shrink) Gamma Factor The Gamma Factor adjusts the gamma of the video output up or down. The default value of 1. 00 leaves gamma unchanged. The command is: MENU Output Configs [Config] Color Mgmt Gamma Factor OK RadianceXS 20 rev 11/12/09 Section 5 ­ Configuration Copy Output Settings This command copies the current output configuration to the selected output configuration or configurations. You can choose whether to copy the mode settings, shrink settings, aspect settings, color management settings and other settings. The command is: MENU Output Copy OK Input Configuration Commands After the output is configured, calibrated, and saved, calibrate one input. Then copy that configuration to all the other configuration memories. Then calibrate for differences in the other inputs. To program one of the independent input memories, select the input, then select the configuration memory and use the menu to configure the input. For example, if memory A been calibrated and a second configuration is needed, start by copying Memory A to memory B for that input to reduce setup time for the second configuration. HDMI Input Setup Inputs 1, 2, 3, 4, 5 and 6 are HDMI. By default the appropriate color space is automatically selected ("Auto" mode) for standard-definition "Bt. 601" or high-definition "Bt. 709. " The "Auto" mode is generally best, but some upscaling sources do not convert the color format to Bt. 709 as they should and so "Bt. 601" would be manually selected for these if they are programmed to output HD formats. The command is: MENU Input Video Setup [Resolution] Picture Color Format OK HDMI Video Type By default the HDMI input format is detected automatically. For DVI sources that do not report their format, the input format can be selected manually. The command is: MENU Input HDMI Setup Type (Auto, YCbCr 444, YCbCr 422, RGB) HDMI Physical Input If desired the input selection for HDMI sources can be assigned to different physical HDMI inputs. This can be useful if a receiver or HDMI switcher is used to switch several HDMI to a single input on the Radiance. Different settings and calibrations for several virtual HDMI inputs can be stored for the same physical HDMI input. [. . . ] '9' leaves message until "ZC" sent. 2 lines, 30 characters per line, legal characters '' through 'z' (0x20 - 0x7a in hex), a carriage return or '{' can be used to terminate message. ASCII extended characters set solid block for use as a volume bar. Set zoom factor to M-- Where M can be 0-2 (or 0-7 if zoom is set for 5% steps) Set output aspect ratio to MMM for all input aspects--. [. . . ]