User manual LUX TX1500 B

[. . . ] INSTALLATION AND OPERATING INSTRUCTIONS TX1500b SERIES SMART TEMP ELECTRONIC THERMOSTAT MO DAY ® UP HEAT PM DOWN MO DAY UP HEAT MO DAY UP HEAT PM DOWN PM DOWN SET SATURDAY PROGRAM SET WEEKDAY PROGRAM SET DAY/TIME SET SUNDAY PROGRAM FILTER RESET FAN AUTO ON HEAT OFF COOL SET SATURDAY PROGRAM SET WEEKDAY PROGRAM SET DAY/TIME SET SUNDAY PROGRAM FILTER RESET FAN AUTO ON HEAT OFF COOL HOLD HOLD RUN RUN NEXT NEXT Patents Pending 1500 TO SET TIME & DAY · Rotate Dial to SET DAY/TIME. · Press UP to change td · Press UP/DOWN to set time. TO SET PROGRAMS · Rotate Dial to SET WEEKDAY Patents Pending 1500 SIMPLIFIED INSTRUCTIONS TO SET TIME & DAY · Rotate Dial to SET DAY/TIME. · Press UP to change · Press UP/DOWN to set time. [. . . ] Press up on the button on bottom of thermostat and swing the body away from the base and up to remove the body from the base. Be careful not to drop the body or disturb electronic parts. Leave the cover closed while the body is being removed from the base. C A U T I O N © COPYRIGHT 2006 LUX PRODUCTS CORPORATION. ALL RIGHTS RESERVED Base Terminals G Y W RH B O RC R W Latch Button If you are mounting the base to a soft material like plasterboard or if you are using the old mounting holes, the screws may not hold. (4. 8mm) hole at each screw location, and insert the plastic anchors provided. Then mount the base as described below. NOTE TYPICAL HOOKUP FOR 2-WIRE 24V HEATING SYSTEM AND MILLIVOLT SYSTEM G Y W RH B O RC TYPICAL HOOKUP FOR 3-WIRE HEAT SYSTEM IF THIRD WIRE IS FAN WIRE G Y W RH B O RC TYPICAL COOLING AND HEATING SYSTEM (4-WIRE) G Y W RH B O RC GAS VALVE FAN 24 VAC TRANSFORMER OR THERMOPILE 110 Figure 8 GAS VALVE FAN GAS VALVE G COOL COMP 24 VAC TRANSFORMER 110 Figure 9 24 VAC HEAT TRANSFORMER 110 Figure 10 ATTACHING WIRES 4. Hold the base against the wall, with the wires coming through wherever it is convenient for wiring. Route the wires to below the terminal block. Position the base for best appearance (to hide any marks from an old thermostat). Attach the base to the wall with the two screws provided. TYPICAL COOLING AND HEATING SYSTEM (5-WIRE) G Y W RH B O RC TYPICAL SINGLE-STAGE HEAT PUMP WIRING G Y W RH B O RC FAN GAS VALVE FAN REMOVE JUMPER BETWEEN RH & RC ADD JUMPER BETWEEN Y&W ALT. CHG. OVER COOL COMP COMP 24 VAC HEAT TRANSFORMER 110 24 VAC COOL TRANSFORMER Figure 11 24 VAC HEAT TRANSFORMER 110 Figure 12 110 Do not allow wires to touch each other or parts on thermostat. Wires must be trapped between black spacer and brass terminal. Also, be sure to tighten securely all 7 electrical terminal screws. C A U T I O N If you have an electric system and the blower does not operate after installation, find the electric/gas heat selector on the back of the body. Move the selector to the ELEC position. NOTE WIRING DIAGRAMS Heating Systems FAN RELAY COOLING COMPRESSOR HEATING CONTROL HEATING TRANSFORMER DAMPER OR CHANGEOVER VALVE (POWERED IN HEAT) INSTALLING BATTERIES/ MAINTENANCE The TX1500 requires batteries to operate your furnace and retain its programming in memory and to light the display. Replace the batteries when the REPLACE indicator appears in the display or at least once a year. Cooling Systems FAN RELAY COOLING COMPRESSOR HEATING CONTROL HEATING TRANSFORMER DAMPER OR CHANGEOVER VALVE (POWERED IN HEAT) REPLACE When replacing batteries, you have approximately 1 minute before programs are lost. Heat Selector SW1 ELECT RL1 GAS 5/2 MIN ON/OFF C/F 24/12H NOTE DAMPER OR CHANGEOVER VALVE (POWERED IN COOL) DAMPER OR CHANGEOVER VALVE (POWERED IN COOL) COOL TRANSFORMER COOL TRANSFORMER G Y W RH B O RC G Y W RH B O RC REPLACE BATTERIES WHEN INDICATOR APPEARS OR AT LEAST ONCE A YEAR. Tape Off Tape Off ** 4 H 5 V Tape Off * Tape Off C G G F R* B * Y V R TC C RH W RC F * If replacing a Honeywell TM-11, tape off wire "R"; connect wire "B" to terminal "RH. " ** If replacing a Honeywell thermostat with a clock wire "C, " tape off wire "C" Heating/Cooling Systems 4- or 5-Wire with One Transformer FAN RELAY COOLING COMPRESSOR HEATING CONTROL HEATING TRANSFORMER DAMPER OR CHANGEOVER VALVE (POWERED IN HEAT) * If both Y and C wire are present, tape off "C" wire. * If you have a "B" wire in your system which is used as a common wire, connecting it to the "B" terminal on this thermostat may damage your system and/or the thermostat. Heating/Cooling Systems 5- or 6-Wire with Two Transformers FAN RELAY COOLING COMPRESSOR HEATING CONTROL HEATING TRANSFORMER DAMPER OR CHANGEOVER VALVE (POWERED IN HEAT) RC TC 1. Remove fresh batteries from their carton. Remove body of thermostat as described at bottom of first column. Install two new Energizer® or DURACELL® "AA" size alkaline batteries in the battery compartment. Observe the polarity marking shown in the compartment. Place body back on wall. Battery Compartment WARNING: Use Energizer ® or DURACELL ® Alkaline Batteries Only. 5. [. . . ] To program temperature. DOWN PROGRAM LOCK To prevent tampering with set programs. The sequence of keys to lock and unlock the program: AM TH MORN HEAT To change the temp. To move to EVE. DOWN To change the temp. Rotate dial to RUN position to start the programs. DOWN NEXT NEXT NEXT HOLD SETTING THE TIME AND DAY SU DAY PM C A U T I O N The TX1500 is protected against normal static electric discharges. [. . . ]