User manual LYNX 4VN170BA

[. . . ] 5600 09000 041 494 (8211) Instructions for use en Index 4 6 7 8 9 10 11 Detergents . 13 15 16 17 19 21 21 22 Safety instructions . Getting to know your appliance Water softener . Filling the special salt container Filling the rinse-aid container Unsuitable dishes . [. . . ] The programmes supplied with your appliance are indicated on the fascia. Type of crockery e. g. china, pots/pans, cutlery, glasses, etc. Type of food remains Soups, casseroles, sauces, potatoes, pasta, rice, eggs, roast or fried food a lot stuck on hard Mixed Soups, potatoes, pasta, rice, eggs, roast or fried food a lot a little Soak with water if dishes have been left inside dishwasher for several days before they are washed Amount of food remains Condition of food remains loosely attached Wash programme Intensive 65° Normal 65° Eco 65° Pre-rinse Programme sequence Pre-rinse 65° Pre-rinse Wash 65° Intermediate rinse Rinse-aid 65° Drying Pre-rinse Wash 65° Intermediate rinse Rinse-aid 65° Drying Wash 65° Intermediate rinse Rinse-aid 65° Drying Pre-rinse Programme selection The most appropriate programme can be identified by comparing the type of crockery, cutlery, etc. , as well as the amount and condition of food remains, with the details contained in the programme overview. If only a small number of dishes have been loaded into the dishwasher, selecting a programme that operates at the next lowest temperature will usually suffice. 15 en Programme data The programme data (duration, energy and water consumption) can be found in the summary of instructions and refers to standard conditions. Greater deviations may be caused by: different quantities of utensils inlet temperature of the water water pressure ambient temperature mains voltage tolerances and appliance-specific tolerances (e. g. temperature, water flow rate, etc. ) The water consumption values refer to water hardness value 2. Washing the dishes Switching on the appliance Turn on the tap fully. Check once again that the spray arms can rotate freely. Select a programme with the programme selector 1 (rotate in a clockwise direction only). The programme starts. Programme sequence indicator While the dishes are being washed, the programme selector rotates in a clockwise direction and indicates how far the programme has progressed. End of programme The programme has ended when the pump noise is no longer audible and the programme selector has reached its initial position (12 o'clock position). Switching the dishwasher OFF Several minutes after the programme has ended: Set the main switch 5 to OFF. (Does not apply when Aqua­Stop unit has been fitted) It is not necessary to reset the programme selector. when they have cooled down. 16 en Interrupting the programme Set the main switch 5 to OFF. If the hot water was switched ON or the appliance has already heated up and then the appliance door opened, leave the door ajar for several minutes and then close. Otherwise, the appliance door may fly open due to expansion. In order to resume the programme, set the main switch to ON again. Maintenance and care You can help prevent faults by checking and maintaining your appliance regularly. This will save time and reduce problems. Therefore you should occasionally examine the inside of your dishwasher. Overall condition of the appliance Check the rinsing compartment for grease and limescale deposits. If you find any deposits: Fill the detergent dispenser with detergent. Start the empty appliance with the programme which has the highest rinsing temperature. Clean the door seal: Wipe the door seal regularly with a damp cloth and remove any deposits. Changing the programme Switch off the main switch 5 . Set the programme selector 1 to the new programme (rotate in a clockwise direction only!). Check whether the detergent dispenser is still closed. Note If the power supply is disconnected while the appliance is operating, e. g. [. . . ] Using the height-adjustable feet, adjust the appliance until it is level. Ensure that the appliance is standing firmly. Waste water connection See the installation instructions for the required connection steps. If required, attach a siphon with drainage spigot. Using the enclosed parts, connect the waste water hose to the drainage spigot of the siphon. [. . . ]