User manual LYNX 4VW460BA annexe 1

[. . . ] en Short Instructions for dishwasher Brief and handy: Everything your dishwasher requires Before using the appliance for the first time, still read the installation and operating instructions! Adjusting the water softening * Ask your water utility company about the hardness value and enter . . . °dH °fH °Clarke mmol/l 0­6 0­11 0­8 0­1, 1 7­16 12­29 9­20 1, 2­2, 9 17­21 30­37 21­26 3, 0­3, 7 22­35 38­62 27­44 3, 8­6, 2 Set value 0 1 2 3 Indicators on appliance Quickly sorted out . . . and proceed as follows . . . Hold down the Start/STOP button. + Simultaneously rotate the programme selector one position in an anti-clockwise direction. [. . . ] The programmes which correspond to your appliance can be found on your appliance fascia. Duration in minutes Intensive 70_ Normal 65_ Eco 50_ Gentle 40_ Quick 35_ Prerinse 630K The programme data are values measured in the laboratory in compliance with Standard EN 50242. Deviations is practice are possible. 115 1, 70 Water consumption in litres 21 Power consumption in kWh 106 1, 46 18 140 1, 05 14 75 0, 85 15 30 0, 70 10 19 0, 10 4 Start the programme Press the Start/Stop button Washing starts . . . (8303) Additional optionsktionen ** Flexible . . . Top basket washing . . . dishes are washed in the top basket only. Timer programming . . . 5 600 057 256 Switch off the appliance Everything o. k. . . . If the programme end indicator illuminates, rotate the programme selector to the OFF position. Turn off the tap. h. ** some models Select programme, press timer programming button: Programme start is postponed by 3 or 9 hours. Maintenance and care Filters Check and, if required, clean: For perfect rinsing results Rotate filter cylinder, remove filter system Rinse under running water Insert Screw on filter system. NOTE MARK! Spray arms Remove blockages/ deposits Pull up lower arm Unscrew upper arm Clean under running water (if required, use a toothpick) Insert lower arm Screw on upper arm Troubleshooting Fault Residual water in appliance . . . Possible causes Programme has still not ended . . . Correct procedure . . . Remedial action Wait until programme ends (programme ends ­ indicator illuminates) or terminate programme (see below). Fault Possible causes Remedial action Plastic/utensil parts discoloured . . . Detergent with reduced bleaching effect . . . Insufficient detergent . . . Use detergent with chlorine bleaching. Observe manufacturer's specifications. Programme does not continue running . . . Programme interrupted . . . Programme selector moved to ineffective position . . . Door is open . . . Continue programme (see Interrupting programme). Close door, programme is automatically continued. Milky coating on dishes (removable) . . . Rinse-aid dosing too high (visible streaking) . . . Rinse-aid dosing too low . . . Reduce or increase dosing according to instructions. Glasses clouded, dull . . . Arrange dishes according to instructions. [. . . ] ­ To continue, press the START/STOP button again. If the door was opened, just close the door again. Terminating the programme . . . ­ Press the START/STOP button (approx. 3 seconds) until the End-of-programme indicator flashes. Arranging dishes correctly . . . Arrange dishwasher-proof dishes in accordance with the operating manual (without residual ash, wax, lubricating grease, ink, sticky labels; remove any large remnants of jam, milk products or food) and check that the spray arms can rotate freely. ­ Wait (approx. 1 minute) until the flashing stops and the Standby indicator illuminates. ­ Restart programme or switch off appliance. [. . . ]