User manual M-AUDIO EQMAN

[. . . ] No table of contents entries found. FCC Radio and Television Interference Statement for a Class 'B' Device This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a CLASS 'B' computing device in accordance with the specifications in Subpart B of FCC Rules and Regulations (as outlined in the Code of Federal Regulation, Title 47), which are designed to provide reasonable protection against such interference in a residential installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and then on, the user is encouraged to try to correct the interference by one or more of the following measures: 1) reorient or relocate the receiving antenna; 2) increase the separation between the equipment and the receiver; 3) connect the equipment into a different outlet so that the equipment and receiver are on different branch circuits; 4) ensure that the card mounting screws, connector attachment screws and all ground wires are secured and tight; and 5) consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. [. . . ] You will be prompted with an "Are You Sure?" dialog which allows you to exit the application, or cancel and continue using the application. The Rom Button The Rom Button pops up a menu of selections regarding the EQMan "Rom": Read One, Read All, Write One, Write All, and View Rom Programs. A description of EQMan Rom operation is included in the MIDI Control of EQMan section. Read One This choice allows you to read any program in Rom (the Rom location) to any program in the current Remote Control program map (called the App location). When you read a Rom program, it will completely overwrite your App location, so be careful about where you read to. Read All Reads all programs from Rom to the application's program map. This function completely overwrites all App programs, so use it carefully. If you wish to keep your current programs before reading 16 the Rom, save the current programs to disk as a map file before using the Read All function. Write One Allows you to select and write any App program to and EQMan Rom program. The selected EQMan Rom program is overwritten. Write All This choice writes all App programs to Rom where they can be accessed via other MIDI applications. All Rom program locations are overwritten. View Rom Programs This selection displays the current application program map. The names and location assignments of all programs currently in EQMan Rom are displayed. This dialog is for information only and no programs are overwritten in App program map and Rom. Below is an example of the information displayed when View Rom Programs is selected. 5 goes here Displaying the Current Rom Program Map The Options Button The Options Button allows you to configure the Remote Control application and set personal preferences. The Options menu has three selections: MIDI Channel, Remote Update Speed, and Volume Fader App preference. MIDI Channel Selects the MIDI channel that will be used to read and write MIDI data to the EQMan Windows driver. This channel should be set identical to the MIDI Channel setting in the Windows Driver Advanced Setup dialog box. The factory default MIDI channel setting is 1 and will work in most cases. Remote Update Speed When another MIDI application (a sequencer for example) is accessing the EQMan, any changes that application makes to the EQ/Volume settings are displayed on the EQMan Remote Control (if it is running). These settings are updated either immediately, or every 50 to 500 milliseconds (1 millisecond = 1/1000th of a second). [. . . ] Midiman manufacturer's code 00, 01, 05. End of sysex. The following system exclusive message(s) may be written to the EQMan or transmitted by the EQMan in response to a request: 28 Current EQ/Volume Data Message Contains current settings of the EQ bands and volumes. For EQ gain codes, see Table 1 below. F0H 00H 01H 05H 01H 00H 01H 00H 0nH 01H lvH rvH eqH eqH eqH eqH eqH eqH eqH eqH eqH eqH eqH eqH eqH eqH F7H Sysex message. Midiman manufacturer's code 00, 01, 05. [. . . ]