User manual MACKIE DS3232

[. . . ] U-NET POWER COMM DS3232 24-BIT / 96kHz DIGITAL SNAKE 1 PUSH PUSH 2 PUSH 3 PUSH 4 PUSH 5 PUSH 6 PUSH 17 PUSH PUSH 18 PUSH 19 PUSH 20 PUSH 21 PUSH 22 PUSH 23 PUSH 1 2 3 4 5 6 17 18 19 20 21 22 23 PUSH 7 PUSH INPUTS 8 PUSH 9 PUSH 10 PUSH 11 PUSH 12 PUSH 13 PUSH 14 PUSH 15 PUSH 16 24 PUSH 25 PUSH 26 PUSH 27 PUSH 28 PUSH 29 PUSH 30 PUSH 31 PUSH 32 7 RETURNS 8 9 10 11 12 13 14 15 16 24 25 26 27 28 29 30 31 32 DS3232 DIGITAL SNAKE Important Safety Instructions 1. Donotblockanyventilationopenings. Installinaccordancewiththe manufacturer'sinstructions. Donotinstallnearanyheatsourcessuchasradiators, heatregisters, stoves, orotherapparatus(includingamplifiers)thatproduceheat. Donotdefeatthesafetypurposeofthepolarizedorgrounding-type plug. Apolarizedplughastwobladeswithonewiderthantheother. [. . . ] This also means that it is less susceptible to voltage sags or spikes, providing greater electromagnetic isolation and better protection against AC line noise. . Fan The DS3232 is fan-cooled and brings air in through the sides and out through the rear. Make sure that cool air is available at the sides of the unit, and that there is room at the rear for the warm air to exit from the enclosure and dissipate. If rack-mounted, make sure the DS3232 is not pulling warm (or hot) air in from the rack, and that the sides and rear are not obstructed. Rear Panel All the connection points (other than the power cord) are located on the front panel for easy accessibility when rack mounted. . POWER Switch This one is self-explanatory. When the POWER switch is turned ON, power is supplied to the DS3232 and the POWER LED on the front panel lights up. DS3232 24-BIT / 96kHz DIGITAL SNAKE R LISTED COMMERCIAL AUDIO EQUIPMENT 65HJ DESIGNED BY MACKOIDS IN WOODINVILLE, WA, USA · MANUFACTURED IN CHINA FABRIQUE EN CHINE COPYRIGHT ©2006 · "MACKIE", AND THE RUNNING MAN FIGURE ARE TRADEMARKS OF LOUD TECHNOLOGIES, INC. · PATENT PENDING. WARNING: RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS: RISQUE DE CHOC ELECTRIQUE -- NE PAS OUVRIR TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL. SERIAL NUMBER MANUFACTURING DATE AND RATING. CAUTION: REPLACE WITH THE SAME TYPE FUSECHANGING FUSE. DISCONNECT SUPPLY CORD BEFORE ~90-265VAC 50-60Hz 85W FUSE: 5A FB POWER DS33 DIGITAL SNAKE Appendix A: Service Information Warranty Service Details concerning Warranty Service are spelled out in the Warranty section on page 15. If you think your DS3232 has a problem, please check out the following troubleshooting tips and do your best to confirm the problem. Visit the Support section of our website (www. mackie. com/support) where you will find lots of useful information such as FAQs, documentation, and user forums. You may find the answer to the problem without having to send your Digital Snake away. These may sound obvious to you, but here are some things you can check. · Try putting the U100 card in another slot (be sure to turn everything off before removing and replacing the card). Is the fan running and unobstructed so it can circulate air through the DS3232?If the DS3232 feels hot to the touch, power off the unit for a few minutes to allow it to cool. Turn the unit back on and, if communication is restored, provide better ventilation so cool air is available to the DS3232. Is the mixing console properly configured to accept the input signals from the DS3232?Make sure the inputs for the mixing console have been setup to accept the 32 input signals from the DS3232. Is the input GAIN control for the channel turned up on the mixing console?Make sure the signal level from the selected input source is high enough to light up some of the INPUT meter LEDs. [. . . ] The address of your closest authorized service center will be given to you by Technical Support along with a Service Request Number. IMPORTANT: Make sure that the Service Request Number is plainly written on the shipping carton. LOUD Technologies reserves the right to inspect any products that may be the subject of any warranty claims before repair or replacement is carried out. LOUD Technologies may, at our option, require proof of the original date of purchase in the form of a dated copy of the original dealer's invoice or sales receipt. [. . . ]