User manual MACKIE SDR24-96

[. . . ] 24/96 SDR 24 Operation Guide 24 TRACK/24 BIT DIGITAL AUDIO RECORDER SDR ERROR 44. 1k TC VARI 48k X2 96 HIGH RESOLUTION NON-LINEAR RECORDER 16 BIT 24 BIT HOURS MINUTES SECONDS FRAMES EXT CLOCK PROJECT: Feel the Love AVAIL: 02:27:26 on EXT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 SELECT SELECT SELECT SELECT POWER DELETE LAST TRACK PROJECT EDIT SETUP AUTO TAKE T-CODE CHASE REWIND FAST FWD STOP PLAY RECORD LOCATE STORE LOOP PUNCH REHRSE ALL INPUT AUTO INPUT 24 TRACK/24 BIT DIGITAL AUDIO HARD DISK RECORDER SDR 24/96 CAUTION AVIS 12. Servicing -- Do not attempt to service the SDR24/96. All servicing should be referred to the Mackie Service Department. Lightning -- Unplug the SDR 24/96 during lightning storms or when unused for long periods of time. [. . . ] Select Zero to reset the current locator time to zero. SETUP SETUP MENU > Record I/O Sync Transp TRANSPORT OPTIONS > Loc1 Loc2 Loc3 Loc4 < TRANSPORT OPTIONS > CurLoc TrOf RelOf RelMd CURLOC: 00:13:57:24 > Zero OK Cancel < CURLOC: 00:13:57:24 5. Press Page Right to change the << >> Inc Dec current locator time. A blinking cursor appears over the first numeral of the current locator time. Use the increment (Inc) and decrement (Dec) buttons to change the highlighted numeral. Use the >> button to move to the next numeral. 6. Press the Page Left button when finished, and then select OK to save the new locator time. Transport Offset Transport offset is a preset amount of time that is added to the transport locator positions displayed. For example, if the transport offset is set to 00:01:00:00, the rewind function will stop at 00:01:00:00 instead of 00:00:00:00. The transport offset time is added to all locates, and to incoming and outgoing LTC and MTC. To set the transport offset time: 1. to enter the TRANSPORT OPTIONS menu. SETUP SETUP MENU > Record I/O Sync Transp TRANSPORT OPTIONS > Loc1 Loc2 Loc3 Loc4 28 SDR 24/96 Operation Guide 3. Press the Page Right button and select TrOf. The current transport offset time appears in the display. Select Zero to reset the transport offset time to zero. < TRANSPORT OPTIONS > CurLoc TrOf RelOf RelMd TRANSOF: 00:01:00:00 > Zero OK Cancel < TRANSOF: 00:02:00:00 5. Press Page Right to change << >> Inc Dec the transport offset time. A blinking cursor appears over the first numeral of the transport offset time. Use the increment (Inc) and decrement (Dec) buttons to change the highlighted numeral. Use the >> button to move to the next numeral. 6. Press the Page Left button when finished, and then select OK to save the new transport offset time. Relative Offset Just as transport offset adds a preset amount of time to the transport locator positions, relative offset subtracts a preset amount of time from the transport locator positions when relative mode is turned on (see "Relative Mode" next). For example, if the relative offset is set to 00:01:00:00, the rewind function will stop at 23:59:00:00 instead of 00:00:00:00 (at 44. 1 kHz and 48 kHz sample rates). The transport offset time is subtracted from all locates as well. To set the relative offset time: 1. Press SETUP to enter the SETUP MENU. SETUP SETUP MENU > Record I/O Sync Transp TRANSPORT OPTIONS > Loc1 Loc2 Loc3 Loc4 < TRANSPORT OPTIONS > CurLoc TrOf RelOf RelMd 2. Press the Page Right button and select RelOf. The current relative offset time appears in the display. [. . . ] Ask Tech Support for current turn-around times when you call for your RA number. We normally send everything back prepaid using UPS ORANGE (three-day air). However, if you rush your recorder to us by Next Day Air, we'll ship it back to you UPS RED (Next Day Air). This paragraph does not necessarily apply to non-warranty service. [. . . ]