User manual MACKIE SP2400

[. . . ] SP2400 Dual-Channel Program Controller/Amplifier Instruction Manual ZONE A MASTER VOLUME ZONE B 3 0 3 6 9 15 30 55 MASTER VOLUME INPUTS INPUTS 3 0 3 6 9 15 30 55 SP2400 MUSIC CONTROLLER A B OVERLOAD ON 1 2 3 4 1 2 3 4 OFF OFF STATUS COMM PORT POWER 115V 60Hz FUSE 115/T8A 220 WATTS 230V 50Hz FUSE 230/T4A 220 WATTS DIRECT PROGRAM INPUTS L GROUND ALL CALL PARALLEL INPUTS PAGING MIC ZONE A ZONE B PHANTOM CONTROL 1234 SP2400 MUSIC CONTROLLER THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGNS INC "MACKIE. ", "MACKIE INDUSTRIAL", AND THE "RUNNING MAN" FIGURE. COPYRIGHT ©2000 ALL RIGHTS RESERVED 1 SERIAL NUMBER MANUFACTURING DATE GAIN +40dB GAIN LOW U LOCAL 2 3 4 STEREO G + ­ HIGH U R 12345678 1234 PRIORITY EXPANSION IN EXPANSION OUT 1 2 3 4 OUTPUT MONO 1 2 3 4 ON - + ­12 +12 ­12 +12 CAUTION: TO REDUCE THE RISK OF FIRE REPLACE WITH SAME TYPE FUSE AND RATING REMOTE CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE DESIGNS INC. · WOODINVILLE · WA · MADE IN USA · FABRIQUE AU USA ZONE B STEREO RIGHT OUTPUT SUITABLE FOR CLASS 2 WIRING +­ 100/ 70V/8 I 0 12345678 AMP ADDRESS RS485 REMOTE AMBIENT MIC MIC/LINE INPUT B PHANTOM GAIN +40dB PAGING MIC VOX PRE OUT G + PROGRAM EQ LOW 80Hz U ZONE A STEREO LEFT HIGH 12k U 3K MIC/LINE INPUT A PHANTOM GAIN +40dB PAGING MIC VOX PRE OUT G + PROGRAM EQ LOW 80Hz U MID U 400 FREQ 1K A G B 1 2 3 G + ­ GAIN LOW U HIGH U 1234 OUTPUT SUITABLE FOR CLASS 2 WIRING +­ 100/ 70V/8 A G B 1 2 3 G + MID U 400 FREQ 1K 3K 250 8k HIGH 12k U ­ ­15 +15 ­15 +15 ­ GAIN LOW U HIGH U 1234 ­ ­15 +15 ­15 +15 I 250 8k ­15 +15 - + ­12 +12 ­12 +12 - + 0 12345678 AMP ADDRESS RS485 REMOTE AMBIENT MIC ­15 +15 AMP IN - + ­12 +12 ­12 +12 - + AMP IN CAUTION AVIS 8. Power Sources -- Connect the SP2400 to a power supply only of the type described in these operation instructions or as marked on the rear panel. [. . . ] In addition, the paging mic and paging control signal are also provided on the EXPANSION bus. LOCAL/REMOTE is a set of eight DIP switches used to select the input source for the channel. Each program input has two switches, one to select the left signal source (odd-numbered switches) and one to select the right signal source (evennumbered switches). Move the switches up to select the local program source, and down to select the remote (external) program source from the EXPANSION bus. STEREO/MONO switches configure each input source for either stereo or mono operation. If the SP2400 is being used in a stereo configuration, leave the switches up. If it's being used in a zone configuration, move the switches down to combine the left and right channels for mono operation. PRE OUT is an unbalanced RCA jack that provides a line-level signal from the preamplifier stage of the SP2400. This provides a method for inserting an external signal processor into the signal chain prior to the amplifier stage. The U-shaped jumper wire should remain installed between the PRE OUT and AMP IN jacks for normal operation. AMP IN is an unbalanced RCA jack that accepts a line-level signal. ZONE A/ZONE B OUTPUTS are 2-pin Phoenixtype connectors that provide speaker-level signals. The SP2400 is shipped with the outputs configured for 70-volt operation in U. S. versions, and 100-volt operation in European versions. Internal jumpers are provided to configure the amplifier for 8 ohm systems as well. Connect the supplied AC linecord to the IEC AC Socket. The AC line fuse is contained in the socket, behind the cover located at the bottom of the socket. Use replacement fuses only as indicated on the rear panel. 115V 60Hz FUSE 115/ T8A 220 WATTS 230V 50Hz FUSE 230/ T4A 220 WATTS DIRECT PROGRAM INPUTS L GROUND ALL CALL PARALLEL INPUTS PAGING MIC ZONE A ZONE B PHANTOM CONTROL 1234 SP2400 MUSIC CONTROLLER THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGNS INC "MACKIE. ", "MACKIE INDUSTRIAL", AND THE "RUNNING MAN" FIGURE. COPYRIGHT ©2000 ALL RIGHTS RESERVED 1 SERIAL NUMBER MANUFACTURING DATE GAIN +40dB GAIN LOW U LOCAL 2 3 4 STEREO G + ­ HIGH U R 12345678 1234 PRIORITY EXPANSION IN EXPANSION OUT 1 2 3 4 OUTPUT MONO 1 2 3 4 ON - + ­12 +12 ­12 +12 CAUTION: TO REDUCE THE RISK OF FIRE REPLACE WITH SAME TYPE FUSE AND RATING REMOTE CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE DESIGNS INC. · WOODINVILLE · WA · MADE IN USA · FABRIQUE AU USA ZONE B STEREO RIGHT OUTPUT SUITABLE FOR CLASS 2 WIRING +­ 100/70V/8 I 0 12345678 AMP ADDRESS RS485 REMOTE AMBIENT MIC MIC/LINE INPUT B PHANTOM GAIN +40dB PAGING MIC VOX PRE OUT G + PROGRAM EQ LOW 80Hz U ZONE A STEREO LEFT HIGH 12k U 3K MIC/LINE INPUT A PHANTOM GAIN +40dB PAGING MIC VOX PRE OUT G + PROGRAM EQ LOW 80Hz U MID U 400 FREQ 1K A G B 1 2 3 G + ­ GAIN LOW U HIGH U 1234 OUTPUT SUITABLE FOR CLASS 2 WIRING +­ 100/70V/8 A G B 1 2 3 G + MID U 400 FREQ 1K 3K 250 8k HIGH 12k U ­ ­15 +15 ­15 +15 ­ GAIN LOW U HIGH U 1234 ­ ­15 +15 ­15 +15 I 250 8k ­15 +15 - + ­12 +12 ­12 +12 - + 0 12345678 ­15 +15 AMP IN AMP ADDRESS RS485 REMOTE AMBIENT MIC - + ­12 +12 ­12 +12 - + AMP IN SP2400 ­ 5 3. Installation Application Diagrams Jukebox Remote Control Cassette or DAT Recorder +3 0 ­3 ­6 ­9 ­ 15 ­ 30 ­ 55 Digital Satellite Service CD Player SP2400 SWITCH SETTINGS INPUT 4 PRIORITY OFF/ON Paging Mic AMBIENT MIC OFF/ON DOWN 1234 ZONE A MASTER/SLAVE To Telephone System Music-On-Hold UP I 0 12345678 ZONE B OFF ON 230/115V 50/60 Hz FUSE 115/T8A DIRECT PROGRAM INPUTS L L PAGING MIC GROUND ALL CALL PARALLEL INPUTS ZONE A ZONE SP2400 MUSIC CONTROLLER OFF ON THE FOLLOWING ARE TRADEMARKS OR REGISTERED TRADEMARKS OF MACKIE DESIGNS INC "MACKIE. ", "MACKIE INDUSTRIAL", AND THE "RUNNING MAN" FIGURE. COPYRIGHT ©2000 ALL RIGHTS RESERVED 1 SERIAL NUMBER MANUFACTURING DATE B GAIN +40dB GAIN LOW U PHANTOM CONTROL I 0 12345678 AMP ADDRESS LOCAL 1 2 3 4 LOCAL 2 3 4 STEREO R G + ­ HIGH U 12345678 1234 PRIORITY 1234 EXPANSION IN EXPANSION OUT 1 2 3 4 OUTPUT MONO 1 2 3 4 ON - + ­12 +12 ­12 +12 CAUTION: TO REDUCE THE RISK OF FIRE REPLACE WITH SAME TYPE FUSE AND RATING REMOTE CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE DESIGNS INC. [. . . ] CAUTION: These servicing instructions are for use by qualified personnel only. To avoid electric shock, do not perform any servicing other than that contained in the Operating Instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. Make sure the power is off and the power cord disconnected before removing the top cover to gain access to the inside of the SP2400. Connecting the RS485 Serial Port This is a 3-pin Phoenix-type connector that follows standard RS485 protocol. [. . . ]