User manual MAGIC CHEF MCBC580DBT

[. . . ] Wine Cooler Beverage Cooler Wine Cooler Model No. 10 To ensure proper use of this appliance and your safety, please read the following instructions completely before operating this appliance. Wine Cooler, Beverage Cooler Thank you for purchasing this appliance. We hope it will successfully serve your requirements for many years. SAVE THESE INSTRUCTIONS 2 Before Putting Into Use . 2 Disposing of Worn Out Appliances Tips for Energy Savings Installation . 3 Built-in Installation Free Standing Installation Description of the Appliance . [. . . ] To replace, put the sides of the rack back onto the supporting guides of the cabinet and push back until the rack tabs snap into place. Note: Make sure the tabs on the rack are well engaged in place before loading any bottles. The top five racks each holds 8 bottles with the necks alternating front to back. The bottom rack consists of two stories, each of which holds 6 bottles with the necks facing the front. Interior Light The appliance has an interior light (E14 socket, max. 15W) for easy interior visibility. WE RESERVE THE RIGHT TO ALTER THE SPECIFICATIONS WITH NO EFFECT ON THE OPERATION OF THE APPLIANCE. 4 Temperature Control and Display Wine Cooler MCWC50DBT Beverage Cooler MCBC580DBT The temperature range of the wine cooler is intended for 43°F to 64°F (+/- 5°F ). Average temperature for red wine is 54°F to 61°F. Average temperature for white wine is 43°F to 50°F. The display usually shows the average temperature of the appliance at that moment. PRESET WINE ZONES: Press the [Red] or [White] pads to choose preset storage conditions for Red or White Wine. (The indicator 'RED' or 'WHITE' will light accordingly. ) The programmed Temperature for red or white wine will be displayed for a few seconds. MANUAL TEMPERATURE SETTING: The temperature of the wine cooler can be set anywhere between 43°F to 64°F by the temperature up and temperature down pads as follows: (1) Press the [SET] pad until you hear a "beep" sound (approximately fifteen seconds). (2) Press the pads to increase or decrease the desired temperature in increments of one degree. (3) Press the [SET] pad to confirm your choice - if confirmation is not made within ten seconds the unit will go back to the previous setting. NOTE: The temperature display can be changed between Celsius and Fahrenheit by pressing and holding the pad for approximately 10 seconds. . The temperature range of the beverage cooler is intended for 41°F to 54°F (+/- 5°F ). . The display usually shows the average temperature of the appliance at that moment. NORMAL TEMPERATURE SETTING: Whenever the appliance is switched on, or the NORMAL' pad is pressed, the appliance runs on the 'NORMAL' setting of 45°F and the 'NORMAL' indicator lights. MANUAL TEMPERATURE SETTING: The temperature of the beverage cooler can be set anywhere between 41°F to 54°F by the temperature up and temperature down pads as follows: (1) Press the [SET] pad until you hear a "beep" (approximat (2) Press the pads to increase or decrease the desired temperature in increments of one degree. (3) Press the [SET] pad to confirm your choice - if confirmation is not made within ten seconds the unit will go back to the previous setting. The 'MANUAL' indicator lights when the appliance runs on 'MANUAL' setting. The temperature display can be changed between Celsius and Fahrenheit by pressing and holding the pad for approximately 10 seconds. The following is applicable to both MCWC50DBT and MCBC580DBT: To return the controller back to the Factory Setting, press and hold the pad, within one second press pad and continue holding both for approximately 10 seconds, until you hear a "beep" sound signaling that the controller is back to the original Factory Setting. The indicator indicates status of the refrigeration cycle as follows: (1) It flashes before the compressor starts; (2) It remains ON during the refrigeration cycle; (3) It remains OFF during the idle cycle. [. . . ] Note: If desired, change the door swing before installation. Appliance Warranty MC Appliance Corp. warrants each new Appliance to be free from defects in material and workmanship and agrees to remedy any such defect or to furnish a new part(s) (at the company's option) for any part(s) of the unit that has failed during the warranty period. Parts and labor expenses are covered on this unit for a period of one year after the date of purchase. warrants the compressor (parts only) to be free from defects in material and workmanship for a period of 5 years. [. . . ]